Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
The wire which is coloured blue must be connected to the terminal which is marked with the N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the appliance must be earthed, DO NOT use 2-pin socket outlets, if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size ie. 0.75mm2 cross sectional area and temperature rating of 85°C eg. heat resisting PVC. IF A MOULDED PLUG IS FITTED In the event of replacing a fuse in the plug supplied a 3amp ASTA approved fuse to B.S.1362 must be fitted. Note: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse cover can be obtained from your local Electrical Retailer. The colour of the correct replacement fuse cover is that of the coloured marks or inserts in the base of the plug. GB 9 GETTING TO KNOW YOUR COOKER HOOD The Controls L Light Switches the lighting system L Light Switches the lighting system on and off. on and off. M Motor Switches the extractor motor M Motor Switches the extractor motor on and off. on and off. V Speed Sets the operating speed of V Speed Varies the operating speed the extractor: of the extractor, from 1. Low Speed, used for a minimum - used for a continuous and silent continuous and silent air air change in the change in the presence of presence of light light cooking vapour, to cooking vapour. maximum - used for 2. Medium Speed, eliminating the highest suitable for most cooking vapour emission, operating conditions. including long periods. 3. Maximum Speed, used for eliminating the highest cooking vapour emission, including long periods. WARNING: Children should not be allowed to play with the appliance or tamper with the controls. GB 10 CARE AND CLEANING Before cleaning your cooker hood or carry out any maintenance, switch off and remove the plug from the socket to disconnect it from the electricity supply. Grease Filters CLEANING METAL SELF- SUPPORTING GREASE FILTERS The filters must be cleaned every 2 months of operation, or more frequently with heavy usage, and can be washed in a dishwasher. • Remove the filters one at a time by pushing them towards the back and pulling down at the same time. • Wash the filters, taking care not to bend them. Allow them to dry before refitting. • When refitting the filters, make sure that the handle is visible on the outside. CLEANING MULTILAYER METAL GREASE FILTERS The filters must be cleaned every 2 months of operation, or more frequently with heavy usage, and can be washed in a dishwasher. • Release the filter retaining grill using the lateral sliding handles. • Remove the filter retaining clips. • Remove and wash the filters. Allow them to dry before refitting. • Replace the filters on the grill, fix them in position using the filter retaining clips and close the filter retaining grill. REPLACING SYNTHETIC GREASE FILTERS The filter is not washable, it must be replaced approximately every two months of use, or more frequently with heavy usage. • Release the filter holder frame using the lateral sliding handles. • Remove the filter retaining clips. • Replace the saturated synthetic filter. • Fix the new synthetic filter using the retaining clips and close the filter holder frame. GB 11 CARE AND CLEANING CHARCOAL FILTER: REPLACING THE ACTIVATED CHARCOAL FILTER The filters are not washable and must be replaced after every 4 months of operation, or more frequently with heavy usage. • Remove the grease filters. • Remove the saturated activated charcoal filters as shown (A). • Dispose of the charcoal filters. • Fit the new filters (B). • Replace the grease filters. LIGHT REPLACEMENT 15W neon light 40W incandescent light 20W halogen light • Remove the metal terminals T fixing the glass cover or the metal panel. • Slide the glass cover or the metal panel to the right until the left hand end is free. Lower it slightly and slide it to the left to free it completely. • Replace the light with a new one of the same type and rating. • Replace the glass cover or the metal panel in the reverse order. CLEANING • Clean with a sponge soaked in warm water and a sodium bicarbonate solution, which is among other things a good disinfectant. If you do not have any, you can use a neutral soap. • DO NOT use abrasive detergents, bleach or detergents using ammonia. • NEVER use solvent based products. Failure to carry out the basic standards of cleaning and replacement of the filters could cause a firerisk. Therefore you must observe these instructions. GB 12 NOTES GB 13 After...
Dieses Handbuch ist für folgende Modelle:Ventilatoren - HE91 (1.58 mb)