Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: AEG Dateigröße: 818.47 kb Dateiname: Unterrichtssprache:

The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting and outlets are not blocked. The cooker hood has switched off during operation... The safety cut-out device has been tripped. Turn off the hob and then wait for the device to reset. If the hood has been installed below the heights indicated in the installation instructions the motor will cut-out frequently which will damage the hood. If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 61 Special accessories Charcoal filter KF20 E-Nr. 942 120 600 Technical assistance service (not for UK) You are welcome to telephone our technical assistance service (see list of technical assistance centres) whenever you need information or in the unlikely event of a fault. When calling, please be ready to specify: 1. The model code number 2. The serial number (E-Nr.) 3. The manufacturing number (F-Nr.) This information is shown on the registration plate inside the unit behind the grease filter. We reserve the right to change specifications and colours as a result of our policy of continuing technological development. Service and spare parts for UK In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at Please ensure that you have read the section „What to do if....“ as the engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty. Please note that proof of purchase is required for in-guarantee service calls. Help us to help you Please determine your type of enquiry before writing or telephoning. When you contact us we need to know: • Your name • Address and post code • Telephone number • Clear and concise details of the fault • Name and model of the appliance* • E number* • This information can be found on the rating plate, which can be seen when the grease filters are removed. 62 Technical Specifications Model DD 8890 CHDD 8820 CHDD 8890 Dimensions - extractor version (in cm): Height 70-113 68,S-113,4 Width 89,8 119,8 Depth S0 46 Dimensions - filter version (in cm): Height 78-122 77,2 - 123 Width 89,8 119,8 Depth S0 46 Maximum absorbed power: 21S W 27S W Motor absorption: 1 x17SW 1 x17SW Lighting: 2 x 20 W 4 x 20 W Lengthof the cable: 1S0 cm 1S0 cm Electrical connection: 220 - 240 V 240 V Mounting accessories included 1 chimney support 1 reduction flange 0 12S-120 mm 1 deflector 1 allen spanner (for TORX screws) 1 support bracket 6 wood-screws S x 4S mm (for wall mounting) 6 wall plugs 0 8 mm (for wall mounting) 2 metal screws 2,9 x 6,S (for chimney flue mounting) DD 8890 - CHDD 8890 only 4 metal screws 3,S x 9,S (to affix the deflector to the support) CHDD 8820 only 4 metal screws 2,9 x 6,S (2 for chimney flue mounting + to affix the deflector to the support) Electrical connection (not for UK) Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician. Electrical connection for UK only Safety warnings for the electrician Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. The switch must be accessible at all times. The following is valid in the United Kingdom only: - the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol (_L ), or coloured green or green and yellow; - the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, - - the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. 64 Wall ...

Herunterladen

Geben Sie zwei Ziffern: