Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Kobe Range Hoods Dateigröße: 1.34 mb Dateiname: Unterrichtssprache:

2 3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Duct Cover Box (Sold Separately) {A} KOBE Range Hood {B} Warranty Registration Card {C} Instruction Manual {D} Baffle Filter -- 2 (30”, 36”, 42”) -- 3 (48”) {E} Stainless Steel Spacer -- 0 (30”) -- 1 (36”) -- 3 (42”) -- 2 (48”) {F} Hood-Mounting Bracket w/ Screws Set {G} Rubber Stand {H} Oil Tunnel {A} {B} {C} {D} {E} {F} {G} {H} {I} KOBE Duct Cover (Model No. CH1120DC) {J} Inner Duct Cover-Mounting Bracket {K} Outer Duct Cover-Mounting Bracket {L} Screws Package {I} {J} {K} {L} FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE WWW.KOBERANGEHOODS.COM OR CONTACT KOBE RANGE HOODS AT (626) 350-1355. 3/16" X 1/2" (8 pcs) Rubber Stand (2 pcs) Inner Duct Cover Outer Duct Cover 1/8" X 3/8" (4 pcs) INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1 or TABLE 2. (All calculation in inches.) -FOR UNDER THE CABINET TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Preferred Height of Counter Top to Hood Bottom (Recommended 27” to 30”) D = Height of Hood E = Height of the Cabinet -FOR STAND ALONE (WITH OPTIONAL DUCT COVER) TABLE 2 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Preferred Height of Counter Top to Hood Bottom (Recommended 27” to 30”) D = Height of Hood E = Height of Duct Cover [F – D] F = Height of the Hood Installation [A – (B+C)] 4 SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. Installation Contents UNDER THE CABINET INSTALLATION ........................................................................6 PREPARATION BEFORE INSTALLATION ............................................................................. 6 HOOD INSTALLATION ...................................................................................................... 6 DUCTWORK INSTALLATION.............................................................................................. 7 WIRING TO POWER SUPPLY............................................................................................ 7 ACCESSORIES................................................................................................................ 8 FINAL ASSEMBLY............................................................................................................ 8 STAND ALONE INSTALLATION.....................................................................................9 PREPARATION BEFORE INSTALLATION ............................................................................. 9 HOOD PREPARATION BEFORE INSTALLATION ................................................................... 9 HOOD INSTALLATION ...................................................................................................... 9 WIRING TO POWER SUPPLY.......................................................................................... 10 DUCT COVER INSTALLATION ......................................................................................... 11 ACCESSORIES.............................................................................................................. 11 FINAL ASSEMBLY.......................................................................................................... 12 5 UNDER THE CABINET INSTALLATION Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood, if any. • Use duct tape to seal joints between pipe sections. • For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not provided) on each side. Refer to Figure 2. • Using references in TABLE 1 and Measurements and Diagrams on page 18, create access opening for electrical wires and hood exhaust under the cabinet. Hood Installation CAUTION: If moving the cooking range is necessary to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 3. 2. If necessary, attach two rubber stands (provided) with 3M adhesive tapes (provided) to the back corners of the hood. 3. Using references in TABLE 1 and Measurements and Diagrams on page 18 center the hood beneath the cabinet and flush with the fr...

Herunterladen

Geben Sie zwei Ziffern: