Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for grounding. • DO NOT ground to a gas pipe. • DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock. • Check with a qualified electrician if you are in doubt as to whether the rangehood is properly grounded. • Failure to follow electrical requirements may result in a fire. GB 0 0 0 0 0 0 0 0 0 0 aaaaaaaaaaaaaaaaaaaaaaaaaaaa0 5 0 aaaaaaaaaaaaaaaaaaaaaaa0 aaaaaaaaaaaaaaaaaaaaa0 INSTALLATION 0 aaaaaaaaaaaaaaaaaaaaaaa0 aaaaaaaaaaaaaaaaaaaaa0 This canopy hood is designed to be fixed to any rigid vertical surface, over a gas or electric hotplate and can be used either in the extraction mode (ducted to the outside) or in the recirculation mode (internal recycling). Warning PERSONAL INJURY HAZARD Because of the weight and size of the rangehood canopy, two or more people are needed to move and safely install the rangehood canopy. Failure to properly lift rangehood could result in damage to the product or personal injury. Components The hood comprises the following (fig.1 ): • No.1 canopy C complete with controls, lighting and ventilator unit • No.1 telescopic chimney, comprising: No.1 upper chimney element S No.1 lower chimney element I • No.2 directional grills G • No.1 recirculation spigot R • No.2 additional side recirculation spigots P1 • No.1 bag containing: No.2 brackets 2 to fix the chimney, screws, rawl plugs and documents. • No.1 splashback B (optional) Installation instructions For easy installation, proceed as follows: • Fitting the wall brackets and Splashback • Fixing the canopy • Electrical connection and working test • Ducting or Recirculation fitting • Fitting the telescopic chimney Fitting the wall brackets and Splashback Please refer to (fig.2a-b): • Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling, using a marking pen. This is to ensure the correct vertical alignment of the various parts. • Fixing the wall brackets item 2: a) Place one of the brackets 2 against the wall approximately 1 or 2 mm from the ceiling or from the top limit, aligning its centre (slot) with the vertical line. b) Mark the centres of two keyholes in the bracket on the wall. c) Rest the other bracket 2 against the wall, aligning it with the vertical line, at a distance X measured as shown in fig.2 equal to the height of the upper chimney element S supplied with the hood. The position X may vary, according to the various sizes of upper chimney element available. d) Mark the centres of the keyholes in the bracket on the wall. 6 0 0 0 0 0 0 0 0 0 0 aaaaaaaaaaaaaaaaaaaaaaaaaaaa0 GB 0 aaaaaaaaaaaaaaaaaaaaaaa0 aaaaaaaaaaaaaaaaaaaaa0 • Drilling fixing holes item 1: a) Mark a point on the vertical line at a distance from the cooking appliances of: d =1000 min (distance without splashback). d =height of splashback + 350 mm (distance with splashback).The distance H is the minimum height in mm from the cooking appliances to the bottom edge of the front panel of the hood. b) At the point marked, draw a horizontal line parallel to the cooking appliances. c) Drill two holes in the wall 1 using an 8 mm drill bit (fig.2a), and insert the rawl plugs and screws into the holes 1 (4.2 x 44.4 screws). Fix the screws, leaving a space of 5-6 mm required to hook up the canopy. Small adjustments can be made using the hood adjustment screws (see Fitting the canopy). The hood should have a maximum excursion of 20 mm. • Splashback (optional) When a splashback is to be fitted, the distance between the hood and the cooking appliances will be determined by the height of the splashback B and whether or not there is a raised back on the worktop. The splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes, care must be taken to ensure that the splashback is fitted at the correct height before fixing the base units or at least the worktop covering them. As this is a complex operation, it should only be undertaken by the technician installing the kitchen units or by a competent person who knows the final dimensions of the units. If the splashback is to be fixed through the top fixing holes only, proceed as follows: a) Rest the splashback on the worktop and against the wall, as illustrated in fig.2 . b) Mark the centres of the two holes in the top surface. c) Drill the wall using an 8 mm drill bit, and fix the splashback using the rawl plugs and screws provided. d) If necessary, the installer should secure the splashback to the wall by tucking the bottom edge down behind the rear of the worktop. Fixing the canopy Before starting to fix the canopy it will be necessary to adjust the support brackets S1 by turning the adjustment screws in a clockwise direction until their reach their limit (Fig.3): a) Hook the canopy onto the two size 4.2 x 44.4 screws 1 fi...
Dieses Handbuch ist für folgende Modelle:Ventilatoren - KD 6500.1 (728.26 kb)
Ventilatoren - KD 6500.1 (728.26 kb)