Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
• Sleep Mode after one-hour inactivity to pre s e rve battery life 1 Congratulations on your purchase and welcome to the growing number of cyclists who are discovering a powerful new generation of bicycle computers. Your Specialized SpeedZone® Team has been designed to provide the best combination of perf o rmance, f e a t u res, durability and ease of use and installation. The following functions available on your 1 2 3 4 5 6 7 1 2 3 4 5 6 7 What is included in you SpeedZone® Te a m p a c k a g e : 1. SpeedZone® Team Computer (1) 2. Mounting bracket (2) 3. Magnet with screw (1) 4. Cable tie wraps (4) 5. Mounting bracket sizing straps (3) 6. Transmitter (1) 7. Transmitter mounting bracket (1) Mounting the SpeedZone® Te a m : The SpeedZone® Team Wi reless transmitter can mount on the right or the left side of the fork blade. The right side should be used on large frames or when a suspension fork is installed. The optimal distance between the computer and the transmitter is 24 inches (610mm) The distance may need to be less that 24 inches (610mm) if ambient temperatures are below 40 °F (4 °C). To reduce signal loss in colder t e m p e r a t u res, the transmitter should be mounted as close to the computer as possible. (maximum mounting distance is 28 inches). Use the transmitter mounting bracket and tie-wraps provided to position the sen s o r. Do not tighten the tie-wraps until final placement 2 4 i n . m a x 1 - 2 m m f i g . 1 f i g . 2 of the magnet is correct. See figure 1. Attach the magnet to a spoke across fro m the transmitter with the magnet scre w. The clearance between the magnet and the transmitter should be approximately 1 / 3 2 ” 1/ 16” (1-2mm). Tighten the magnet and t r a n s m i t t e r. Do not over-tighten the magnet s c rew See figure 2. Attach the mount to the handlebar using the bracket screw provided. Tighten so that the bracket cannot rotate on the handlebar. T h e re are several sizing straps provided to fit d i ff e rent diameter bars See figure 3. the computer forw a rd onto the mounting until it ‘snaps’ into place with an audible click. To remove the computer, push it back- w a rd until it releases from the mount. To test for proper installation of the magnet, transmitter and computer, activate the computer by pushing the ‘MODE’ (right side) button and pick up the front of the bicycle and spin the wheel. The “wheel option” indica f i g . 3 tor will flash. If it does not flash, check the sensor and magnet alignment. Realign as n e c e s s a ry until the “wheel option” indicator flashes while spinning the wheel. P ro g r a m m i n g : P rogramming the functions of your SpeedZone® Team re q u i res it to be placed in various “modes” (i.e. odometer mode, distance mode). The computer can be cycled through these modes by pressing the “MODE” button located on the right-hand side of the housing. Once a specific mode has been entered, its values can be reset or adjusted by pressing either the “FUNCTION” button located on the left hand side of the housing or by using a combination of the “MODE” and “FUNCTION” buttons. 1. Miles or Kilometers selection: Your SpeedZone® Team will re c o rd speed and distance in either miles (M/h) or kilometers (KM/h). To enter your selection of miles or kilometers, push the “MODE” button until ODO (odometer) appears in the lower left side of the display (This is called the odometer mode). Hold down the “FUNCTION” (left side) button and ‘tap’ the “MODE” button once. The Km/h, m/h indicator will begin blinking. You may now a l t e rnate between miles and kilometers by p ressing the “MODE” button. When the c o rrect choice is flashing, select it by pre s sing the “FUNCTION” button. You will now enter the “Programmable Odometer” mode. If the odometer setting is correct push the “FUNCTION” button (5 times) to exit to odometer mode (otherwise, see “Setting the p rogrammable odometer below). 2. Setting the P ro g r a m m a b l e O d o m e t e r : The pro g r a m m a b l e odometer mode is accessed by entering the odometer (ODO) mode and holding down the “FUNCTION” button and ‘tapping’ the “MODE” button once. The Km/h indicator will flash. If the Km/h setting is c o rrect press the “FUNCTION” button once and a five digit number will appear. Yo u a re now in the programmable odometer mode. This mode is useful if you have replaced the battery and would like to retain the mileage you have already ridden. To enter a mileage into the odometer, p ress the “MODE” button until the flashing digit is correct. (Note: The “MODE” button may be held to scroll to the correct digit.) P ress the “FUNCTION” button to select the next digit to the right. Repeat the pro c e s s until all five digits are entered as your existing mileage. 3. Wheel Circ u m f e rence Selection: To set the circ u m f e rence for the type of tire s you are using, you can use Specialized’s exclusive “Easy Calibration Mode” or meas u re your actual tire circ u m f e rence by the roll-out method. Two diff e rent t...