Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Do not use the stand for ordinary, flat-bottomed saucepans. The wok stand MUST BE PLACED ONLY over the pan support for the triple ring wok burner. The cooktop becomes very hot during operation. Keep children well out of reach. Cooktop troubleshooting Problem Possible solutions My cooktop burners do not light Check the cooker is switched on. Check the gas supply valve is turned on and the supply to the house is working. You should hear the gas when you turn a burner on. The ignitors may be dirty. Clean them with a toothbrush and methylated spirits. The burner parts may not be located properly. Check the assembly and make sure the burner cap is sitting flat. My burner flames are yellow or hard to start The burner parts may not be located properly. Check the assembly and make sure the burner cap is sitting flat. If you use bottled gas this may indicate you are getting near the end of the bottle. Check the burner parts are clean and dry. The gas pressure may not be at the correct level. Check with your service person or installer. Your cooker may not be set up for the gas you are using. Check this with your service person or installer. One of my burners has an uneven flame Check the burner parts are clean and dry. Check the assembly and make sure the burner cap is sitting flat. The flame goes out at low settings The gas supply pressure may be low. Check this with your service person or installer. The low setting may have been adjusted incorrectly. Check this with your service person or installer. My burners do not turn down much (when running on bottled gas or LPG) Your cooktop may not have been adjusted correctly. Check this with your service person or installer. The flame tips are very yellow Call your service person to service the cooker. There are objectionable odours Call your service person to service the cooker. The flame appears to lift off the burner Call your service person to service the cooker. There is an electricity failure If there is an electricity failure, you can still use your cooktop. Light the burners by holding a match close to the side of the burner and turning the control knob to the High position. Wait until the flame is burning evenly before adjusting. Using your multifunction oven for the fi rst time Using your oven for the first time Clock display Function knob Temperature Control buttons knob Figure 23 Main oven controls Before using your new oven, please: 1 Read this user guide, taking special note of the ‘Safety and warnings’ section. 2 Remove all accessories and packaging. 3 Set the clock. The oven will not work until the clock has been set. 4 Condition the oven: Put in the shelves and trays. Fit them between the metal runners, with the safety stop notch down and at the back. (If the shelf supports are not already fitted, see ‘Care and cleaning’ for how to do this). Heat the oven on maximum for: 60 minutes in the position 30 minutes in the position 15 minutes in the position 5 Wipe out the oven with a damp cloth and mild detergent, and dry thoroughly. Figure 24 Correct position of shelves and pan Clock and timer Buttons: Timer Cooking time End of cooking time Decreases the number shown on the display or changes the volume of the beeps Increases the number shown on the display Illuminated symbols: A - flashing - oven in automatic position but not set A -steady illumination - oven set for automatic cooking Cooking taking place Timer in operation Setting the clock When first connected, or after a power failure, ‘0.00’ will flash on the display. To set the clock, press the and buttons together and then the and buttons. Note: Changing the time will delete any automatic program. Using the timer The timer can be set for up to 23 hours and 59 minutes. To set the timer, press the button, then the and buttons. To check the remaining time press the button. When the time is up, the timer will beep. Press the button to turn it off. Note: if ‘A’ is flashing on the display, press the and buttons together. Setting the timer volume You can select from three volume levels by pressing the button. Figure 25 Clock display and control buttons Using your oven Figure 26 Function knob Figure 27 Temperature knob 1 Select the function using the function knob. The oven lights will come on. 2 Select the temperature using the temperature control knob. The oven temperature indicator light, above the temperature knob on the control panel, will glow until the oven has reached the set temperature, and then it will go out. 3 When you have finished cooking, turn the function and temperature control knobs to the off O position. Note: if ‘A’ is flashing or steadily illuminated on the display, press the and buttons together. Cooking functions OVEN LAMP Only the oven light comes on. It remains on in all the cooking functions. BAKE The upper and lower heating elements come on. BAKE is the traditional method of cooking. It is best to cook on only one shelf at a time in this function. GRILL The grill at the top of the ove...