Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Bosch Dateigröße: 1.77 mb Dateiname: Unterrichtssprache:

Make sure rear edge of cooktop does not bind against front of snorkel. Follow the manufacturer’s installation Instructions for installing gasket strips, protective heat tape (if required), securing the cooktop to the countertop and making the cooktop electrical and/or gas connections. Note: Check boxes as tasks are completed. Internal Blower Strain Relief 6 Pin Connector Remote or Inline Blower (see Figures 10 and 11 for further detail): Y A. Remove junction box cover and connect conduit with 5 wires from remote blower. Hook up wires per Wiring.Fig. 10. Replace junction box cover. Y B. Attach Duct Transition Box at mounting holes with sheetmetal screws. Y C. Feed remote blower pigtail through strain relief. Y D. Attach strain relief to downdraft near junction box. Y E. Connect pigtail to downdraft at 6 pin connector. Y F. Run pigtail wires to junction box. Y G. Inside junction box, connect conduit with five wires from remote or inline blower. Use a conduit connector to secure. Note: Blower and duct transition box may be installed with duct outlet left, down or right. Install blower or duct transition in such a way that access panels can be removed for service. Y H. Place the cooktop in countertop opening with the rear edge of cooktop overlapping the front edge of the vent. Make sure rear edge of cooktop does not bind against front of snorkel. Follow the manufacturer’s installation Instructions for installing gasket strips, protective heat tape (if required), securing the cooktop to the countertop and making the cooktop electrical and/or gas connections. Note: Check boxes as tasks are completed. Strain Relief Remote Blower Pigtail 6 Pin Connector Junction Box Duct Transition Box Conduit To Remote Blower Fig. 10 – Remote Blower Wiring Diagram Fig. 11 15 WARNING: POWER MUST BE DISCONNECTED BEFORE SERVICING THIS APPLICANE SW POSITION SHOWN WITH DOWNDRADT IN LOWERED POSITION ABBREVIATIONS: C = COMMON NO = NORMALLY OPEN NC = NORMALLY CLOSED POWER 3 WIRE SINGLE PHASE 60 Hz L1: 120 V N: GROUNDED WHITE WIRE SPEED 1 RED WIRE SPEED 2 BLUE WIRE SPEED 3 BROWN WIRE GND: GROUNDED GREEN WIRE RATING: 120V-10A control pc board brown Speed 3 blue Speed 2 Speed 1 red white green/yellow green/yellow white brown blue red Step 8: Verify Installation, Operation and Cooktop Alignment Y Before performing this procedure, verify that all packing materials were removed from inside the snorkel and that the grease filters and front panel have been properly installed. Refer to the Care and Use Manual for instructions regarding filter and front panel installation. Y Plug the vent power cord into a proper electrical receptacle and ensure that the circuit is energized. Y A. Raise the snorkel to its fully extended position by pressing the UP/DOWN push-button once. Do not hold the push- button. The elevating motor will stop when the snorkel reaches its full height. (Note: the blower will not operate unless the snorkel is fully raised). Y B. Remove protective tape from top cap. Y C. Turn the blower ON by selecting in turn each of the 3 speeds. Let the blower run several minutes at each speed to evaluate its operation. Y D. With the blower running, lower the snorkel to its fully retracted position by pressing the UP/DOWN push-button once. The blower will immediately turn off. Y E. With the blower on HIGH, close the windows and doors to the area to ensure that fan does not cause back drafting in any outlet vent for another appliance. Y F. Raise and lower the vent again, and check to make sure that the top cap on the snorkel does not catch on the back edge of the cooktop when it is lowered. If interference occurs, adjust the position of the cooktop by moving it against the front edge of the countertop. Failure to eliminate interference may result in permanent damage to the vent. Also, ensure that the vent support legs have been properly secured to the cabinet base using the screws provided. If the vent system does not operate satisfactorily during any of the above procedures, review all steps in these Installation Instructions to ensure that nothing has been omitted or overlooked. Also, refer to the Care & Use Manual for additional information or call Thermador Customer Support 1800- 735-4328. Note: Check boxes as tasks are completed. CONSIGNES DE SECURITE LIRE TOUTES LES INSTRUCTIONS AVANT D'UTILISER L'APPAREIL. LIRE ET CONSERVER CES INSTRUCTIONS AVERTISSEMENT Pour reduire le risque d'incendie, de choc electrique ou de lesions corporelles, observer ce qui suit : A. L'installation et le cablage electrique doivent etre effectues par des personnes qualifiees conformement a toutes les normes et codes applicables, incluant la construction relative au feu. B. Suffisamment d'air est necessaire pour une combustion appropriee et l'echappement des gaz par tirage (cheminee) d’equipement a combustion pour eviter le tirage arriere. Suivre les directives du fabricant d’equipement de chauf...

Herunterladen

Geben Sie zwei Ziffern: