Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: DCS Dateigröße: 430.55 kb Dateiname: 6108f71c-83df-6e64-0d33-4375d7f93b42.pdf Unterrichtssprache:

Plug in the appliance. Turn on the electricity supply. Electrical connection WARNING: THIS APPLIANCE MUST BE EARTHED. All external wiring must comply with the IEE Regulations for the Electrical Equipment of Buildings. The electrical supply can be by either a plug and socket or a permanently wired connection via a double - pole switch. Should the plug (where supplied) not fit the socket in your home, it should be removed and replaced with a suitable plug. Note: If a moulded plug is fitted which is not suitable, it must be cut off and disposed of properly. To avoid the risk of electrocution, the moulded plug must not be left where children might find it and plug it into a supply socket. It must not be used for any other appliance. Three pin plugs to BS1363 with a capacity of not less than 13A must be used and fitted with a 3 amp fuse ‘ASTA’ approved to BS 1362. With moulded plugs, after replacing the fuse the cover must be refitted. If the cover is lost, the plug must not be used until a replacement cover has been obtained from your supplier. The colour of the correct fuse cover is that of the coloured insert in the base of the fuse recess, or stated elsewhere on the plug. Always state this colour when ordering a replacement fuse cover. If you wish to make a direct connection to the mains, an omnipolar switch with a gap between the contacts of at least 3 mm, of suitable rating for the load and complying with the regulations in force, must be installed between the appliance and the mains.The switch must not break a contact in the yellow/green earth wire. NO REAR VIEW YES COPPER PIPE OR STAINLESS STEEL HOSE Service opening in cabinet REAR VIEW BAND CLAMPS Setting the minimum level 1) Light the burner as already described. 2) Turn the tap to the minimum flame position. 3) Remove the control knobs. 4) Use a thin straight screwdriver to turn the by-pass pin located next to the tap rod (see fig. A).If you are converting from natural gas to LPG, turn the by-pass pin fully clockwise. The result should be a small, homogeneous flame which is uniform around the entire burner ring. 5) Finally, check that the burner does not go out when the tap is turned quickly from the maximum to the minimum position. If the lead has to be replaced, only HO5RR-F or HO5RN-F type cables suitable for the load and the operating temperature must be used.In addition, the yellow/green earth wire must be about 2 cm longer than the live and neutral wires. In all cases, the power supply lead must be positioned so that it does not reach a temperature 50°C above the room temperature in any point. One example of an ideal route is shown in the illustration.The cable is guided by means of band clamps fixed to the side of the cabinet, in order to avoid any contact with the appliance underneath the hob. Replacing the power supply lead A Changing the nozzles 1) Remove the pan stands 2) Remove the burner caps and flame caps from the burners. 3) Use a size 7 socket wrench to unscrew and remove the nozzles, replacing them with those corresponding to the type of gas to be used (see table). 4) Reassemble the parts, reversing the operations described above. 5) Then replace the setting data plate (close to the mains gas connection) with the one for the new type of gas (it is in the bag of nozzles provided). If the pressure of the gas used is different from that specified (or variable), a suitable piped gas pressure regulator complying with the standard must be installed on the supply pipeline. Adapting to the different types of gas Setting the minimum level 1) Light the burner as already described. 2) Turn the tap to the minimum flame position. 3) Remove the control knobs. 4) Use a thin straight screwdriver to turn the by-pass pin located next to the tap rod (see fig. A).If you are converting from natural gas to LPG, turn the by-pass pin fully clockwise. The result should be a small, homogeneous flame which is uniform around the entire burner ring. 5) Finally, check that the burner does not go out when the tap is turned quickly from the maximum to the minimum position. If the lead has to be replaced, only HO5RR-F or HO5RN-F type cables suitable for the load and the operating temperature must be used.In addition, the yellow/green earth wire must be about 2 cm longer than the live and neutral wires. In all cases, the power supply lead must be positioned so that it does not reach a temperature 50°C above the room temperature in any point. One example of an ideal route is shown in the illustration.The cable is guided by means of band clamps fixed to the side of the cabinet, in order to avoid any contact with the appliance underneath the hob. Replacing the power supply lead A Changing the nozzles 1) Remove the pan stands 2) Remove the burner caps and flame caps from the burners. 3) Use a size 7 socket wrench to unscrew and remove the nozzles, replacing them with those corresponding to the type of gas to be used (see table). 4) Reassemble the parts, reversing the ope...

Herunterladen

Geben Sie zwei Ziffern: