Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: DCS Dateigröße: 594.73 kb Dateiname: Unterrichtssprache:

Specific instructions for installation of the full backguard or low backguard can be found packaged with the backguard. See also page 5. The backguard must be installed when there is less than a 12" clearance between combustibles and the back of the cooktop (above the cooking surface, see Fig. 5, page10). Fig. 6 Wall Mount Full Backguard (Model #’s BGS-3030, BGS-3036, BGS-3048) Wall Mount Low Backguard (Model #’s BGS-1230, BGS-1236, BGS-1248) 11 ELECTRICAL / GAS CONNECTIONS STEP 5: ELECTRICAL CONNECTIONS Receptacle Box Cover Plate Three Prong Receptacle Power requirements Cooktop: Three Prong Plug • 120 VAC, 60 Hz., single phase 7 Amp. • CS-48: 15 Amp. Max. • CS-36: 15 Amp. Max. (use 15 Amp. circuit) Always disconnect electric supply cord from the wall outlet or service disconnect before servicing this appliance. Observe all governing codes and ordinances whengrounding,inabsence of which, observe National Electrical Code ANSI / NFPA No. Fig. 7 70-1990. RECOMMENDED GROUNDING METHOD This appliance is factory equipped with a power supply cord with a three-prong grounding plug (with polarized parallel blades). It must be plugged into a mating grounding type receptacle, connected to a correctly polarized 120 Volt circuit. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the installer to have the existing receptacle changed to a properly grounded and polarized receptacle in accordance with all applicable local codes and ordinances by a qualified electrician. In the absence of local codes and ordinances, the receptacle replacement shall be in accordance with the National Electrical Code. • The third prong should not, under ANY circumstances, be cut or removed. GAS REQUIREMENTS Verify the type of gas supplied to the location. The cooktop are shipped from the factory set up and adjusted for natural gas or LP (propane), depending on specific model ordered. The unit cannot be converted. NATURAL GAS • Connection: 1/2” N.P.T., Minimum 5/8” dia. flex line. • Pressure: 6” to 14” W.C. LP GAS • Connection: 1/2” N.P.T., Minimum 5/8 dia. flex line. • Pressure: 11”to 14”W.C. A regulator is required at the LP source to provide a maximum of 14”W.C.to the cooktop regulator. 12 HOOK-UP TO GAS SUPPLY STEP 6: HOOK-UP A manual valve must be installed external to the appliance, in an accessible location from the front for the purpose of shutting off the gas supply. Make sure the gas supply is turned off at the wall valve before connecting the appliance. The gas supply connections should be made by a qualified technician and in accordance with local codes or ordinances. In the absence of a local code, the installation must conform to the National Fuel Gas Code ANSI 223.1-1988, latest edition. To prepare the unit for connection to the gas supply, thread the supplied 1/2” pipe nipple into the elbow on the end of the manifold. The elbow is located inside the chassis of the unit, on the end of the manifold, facing down. See fig. 9. It is accessible through the square cutout in the left rear corner of the chassis bottom. Connect the outlet of the regulator to the exposed end of the nipple, connect the flex line from the gas supply to the inlet side of the regulator. NOTE: The arrow on the regulator indicating direction of gas flow should be pointing towards the unit. The flex line for the gas supply must be metal and be approved by an approved certifying agency (AGA, CGA, or UL.). Never use a hose made of rubber or other synthetic material, as the h...

Herunterladen

Geben Sie zwei Ziffern: