Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Indesit Dateigröße: 632.83 kb Dateiname: Unterrichtssprache:

Reset the timer to the correct time of day. Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly heated and completely cooked. 6. To set each function always press and hold the required function button and at the same time press “+” or “–” buttons. Clock/Minute Minder Operation (KD6C7E only) 0.00 -+ 0.00 Minute Minder 0.00 0.00 CLOCKFACE The timer incorporates a 24 hour clock. SYMBOLS A ‘Bell’ symbol will light up when you select a Minute Minder Period and will remain lit for the period set. At the end of the Minute Minder Period, the timer will emit an audible tone and the ‘Bell’ symbol will flash. SETTING THE TIME OF DAY Step 1 Make sure all oven controls are turned off. Step 2 Check the electricity supply to the cooker is turned on. Step 3 When switched on, the display will flash 0.00 Step 4 Press and release both buttons simultaneously. Step 5 Press the ‘+’ button to set the Time of Day. The Time of Day can be adjusted, by using the ‘+’ button to increase the time setting or the ‘-’ button to decrease the time setting. The Time of Day is set if no adjustments are made within 10 seconds. THE TIME OF DAY IS NOW SET. To change the time of day repeat Steps 4 & 5 above. Clock/Minute Minder Operation (KD6C7E only) Here you can set a time period of up to 10 hours, that will count down. When it reaches zero, the timer will emit an audible tone. For Example: If you set 20 minutes, the audible tone will occur 20 minutes later. SETTING THE MINUTE MINDER Step 1 Ensure the time of day is set correctly. Step 2 Press and release the ‘+’ button. Note: Step 3 must be started within 10 seconds, otherwise you must repeat Step 2. Step 3 Press the ‘+’ button to set the required time period. A ‘Bell’ symbol will light up. The time period can be adjusted, by using the ‘+’ button to increase the time period or the ‘-’ button to decrease the time period. Release all buttons, the timer display will show the remaining time period. The ‘Bell’ symbol will remain lit to signify that a time period has been set. At the end of the set time an audible tone will be heard and the ‘Bell’ symbol will flash. Step 4 To cancel the audible tone press the ‘+’ button. To cancel the minute minder period press the ‘-’ button until 0.00 is displayed in the window then release the button. If at any time the display shows flashing zero’s, it is likely that the electricity supply has been interrupted. Reset the timer to the correct time of day. Note: The Timer display will show the minute minder period as follows: Any period up to 99 minutes and 50 seconds The display shows MINUTES and SECONDS (10s intervals) eg. 19 minutes 50 seconds Any period between 100 minutes (1 hour 40 minutes) and up to 10 hours The display shows HOURS and MINUTES eg. 1 hour 41 minutes 0.00 0.00 19.50 1.41 Temperature Conversion Chart Gas Mark °F Main Conventional Oven Top Convection Oven Main Fan Oven 1/2 250 120 110 100 1 275 140 130 120 2 300 150 140 130 3 325 160 150 140 4 350 180 170 160 5 375 190 180 170 6 400 200 190 180 7 425 220 210 200 8 450 – 220 210 9 475 – – 220 Ceramic Hob CAUTION: IF ANY CRACK IN SURFACE BECOMES VISIBLE, TURN OFF THE MAINS COOKER SWITCH. Under no circumstances should the hob be used with aluminium foil in contact with the hob surface. The following boiling plates are located beneath the circular cooking areas: Front Right 6 Heat 1800W Rear Left 6 Heat 1500W Rear Right 6 Heat 1200W Front Left 6 Heat 1200W The cooking areas change colour when heated (become red) indicating which heating element is turned on. The cooking area returns to its original colour when the heating element is switched OFF and cools. Hotplates When the control is turned from the 0 position, the settings on the control panel will show 1 - 6, these are 6 fixed positions for cooking. 6 is the highest setting, for fast cooking. To reduce the heat to cook more slowly or simmer, turn the knob to a lower setting which will vary according to size and type of saucepan, the amount and type of food, and whether or not the lid is fitted. Pans can be placed on the unheated areas of the panel when cooking is finished and before serving food. It is inadvisable at any time to leave a heating element switched on without a pan in position as this wastes energy, and could make soil or rub-off from aluminium pans more difficult to remove. To protect elements against overheating, safety cut-outs have been incorporated with each element. After several minutes with the control at setting 6 the safety cut-out switches the element Off and On continuously, thus preventing any adverse effects that may be caused by an excessive build-up of heat in the cooking area. Setting 1 provides low input for simmering. The control will be Off when the control knob is turned to the O position. If the hob should become cracked, never use until repaired. Always ensure that saucepan handles are positioned safely. Ceramic Hob General Information PANS SHOULD BE: Not concave (bow...

Herunterladen

Geben Sie zwei Ziffern: