Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
GETTING STARTED Remove any labels, stickers or tags attached to the body or soleplate of the iron. Note: Use ordinary tap water for ironing. Do not use water processed through a home softening system. Important: For optimum performance, let the iron stand for 90 seconds before beginning to iron. TO FILL THE WATER TANK 1. Grip the sides of the water-fill cover and pull open (A). 2. Tilt the iron and using a clean measuring cup, pour water into opening until the water reaches the MAX level mark on the water tank (B). Do not overfill. 3. Close the water-fill cover by pushing down until it snaps into place. 4. Plug in the iron. The temperature-ready light comes on (C). Tip: If unsure of a garment’s fiber, test a small area (on an inside seam or hem) before ironing. FOR STEAM IRONING 1. Move the dry/steam selector to the desired steam level (D). 2. Turn the fabric-select dial to appropriate setting (between 4 and 6) for your fabric (E). Read garment’s label to help you determine fabric type. • The temperature-ready light glows until it reaches the appropriate temperature. • The light cycles glows on and off during ironing. 3. When finished ironing, turn the fabric-select dial to lowest heat setting, move the dry/steam selector to and unplug the iron. FOR DRY IRONING 1. Make sure dry/steam selector is set to . You may want to empty the water (see “Emptying Water Tank After Ironing - Optional”). 2. Turn the fabric-select dial to the appropriate setting for your fabric. Read garment’s label to help you determine fabric type. A B C D E 4 • The temperature-ready light glows until it reaches the appropriate temperature. • The light cycle glows on and off during ironing. 3. When finished ironing, unplug the iron and place it on its heel rest. 4. Move the dry/steam selector to . 10-MINUTE AUTO SHUTOFF For your peace of mind, the iron will turn off after 10 minutes of inactivity. • The iron beeps and the auto shutoff light starts blinking to let you know that the iron has stopped heating (F). • As soon as you pick up the iron, it starts heating again. SURGE OF STEAM 1. With the water tank filled to the MAX mark, turn the fabric-select dial to at least setting 4 and wait for the temperature-ready light to go off. 2. To remove tough wrinkles, pump the CLEANMAXMIN button at 5-second intervals for a concentrated blast of steam. Vertical steam 1. Hang the garment to be steamed on a clothes hanger. (Curtains or drapes can be steamed once they are hung.) 2. Move the selector to CLEANMAXMIN. 3. Hold the iron close to, but not touching, the fabric. 4. Pull the fabric tight with your free hand and pump the CLEANMAXMIN button as you move the iron over the fabric (G). SPRAY You can use spray at any setting. Check that the water tank is filled with water. 1. Press the CLEANMAXMIN button (H). 2. If spray is weak, pump the button a few times. EMPTYING WATER TANK AFTER IRONING (OPTIONAL) 1. Unplug the iron and let it cool. 2. Open the water-fill cover. 3. To release the water, hold the iron over a sink with the tip pointing down and to one side. Water will empty out of the water-fill opening (J). Care and Cleaning This product contains no user serviceable parts. Refer service to qualified service personnel. CLEANING OUTSIDE SURFACES 1. Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outer surfaces with a soft cloth dampened with water and mild household detergent. Never use abrasives, heavy-duty cleansers, vinegar or scouring pads that may scratch or discolor the iron. 2. After cleaning, steam iron over an old cloth to remove any residue from the steam vents. SELF-CLEANING To keep the steam vents free of any buildup, follow these instructions about once a month. 1. Fill the water tank below the MAX line. 2. Plug in the iron. 3. Turn the fabric-select dial to 6 and place iron on its heel rest. Allow it to heat until the temperature-ready light goes out and comes on again. 4. Unplug the iron and hold over a sink with the soleplate facing down. 5. Move the dry/steam selector to CLEANMAXMIN. Be careful, as hot water and steam will come out of the steam vents (K). Continue to hold the selector in the CLEANMAXMIN position until all the water has emptied, or until you feel all mineral deposits have been flushed. If necessary, rock iron side to side and front to back. 6. When finished, release the selector, stand the iron on its heel rest and plug it in. Heat for about 2 minutes to dry out any remaining water. STORING YOUR IRON 1. Unplug the iron and allow it to cool. 2. Check that the selector is set to . 3. Store vertically ...
Dieses Handbuch ist für folgende Modelle:Bügeleisen - AS685 (1.54 mb)