Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Sunbeam Dateigröße: 188.62 kb Dateiname: Unterrichtssprache:

The SHOT OF STEAM® feature may be used continuously in approximately 3 second intervals. VERTICAL STEAM (select models only) The vertical steam feature allows your iron to function as a garment steamer. TIP: When using the vertical steam on clothing, hang the clothing on a clothes hanger for best results. Hanging curtains and drapes may also be steamed. To use Vertical Steam: 1. Make sure that the iron has heated up (2 minutes). 2. Hold the iron in a vertical position, with the iron close to but not touching the fabric you want to steam. 3. With your other hand, pull the fabric tight. 4. Press the SHOT OF STEAM® button for approximately 3-second intervals as you move the iron across the wrinkled area. WARNING: To prevent the risk of burns, keep your hand away from the area being steamed. WARNING: DO NOT steam garments while wearing them; this may result in injuries. CLEANING THE ANTI-CALCIUM SYSTEM (select models only) The Simple Press™ iron houses an anti-calcium filter in the reservoir, which eliminates impurities from the water. To prolong the efficiency of this filter: 1. Unplug the iron and allow it to cool. 2. Locate the water cup that accompanied the iron. Fill it with water to the Sunbeam logo in the top right corner. Add 1 teaspoon of salt to the water and fill the water reservoir with this solution. 3. Leave the solution in the water reservoir for 15 minutes, shaking occasionally, and then empty it. 4. Fill the water reservoir a second time with the salt water solution, shaking occasionally, and empty it again after 15 minutes. 5. Fill the tank with fresh water to rinse and empty. The Anti-Calcium System should be cleaned approximately once a month. MOTION SMART® AUTO-OFF FEATURE When the iron is plugged in, the Power Indicator will light steadily, indicating that there is power to the iron. If you leave the iron: • in a horizontal position without moving it, or accidentally tip the iron over, it will automatically stop heating after 30 seconds. The Power Indicator will blink to let you know that the iron has stopped heating. CARACTERISTIQUES DU FER SIMPLE PRESS™ 1. Orifice d’atomisation SPRAY MIST® 2. Orifice de remplissage a volet 3. Cadran de selection des textiles 4. Levier de vapeur 5. Bouton d’atomisation SPRAY MIST® 6. Bouton du jet de vapeur SHOT OF STEAM® / Vapeur verticale (certains modeles seul) 7. Temoin marche-arret MOTION SMART® 8. Cordon articule 360° non emmelant 9. Bouton d’autonettoyage 10. Reservoir translucide 11. Semelle 12. Indicateur Storage Strip™ 13. Systeme anti-tartre (certains modeles seul) or facing, before ironing a visible area. Start with a low temperature and gradually increase the heat to find the best setting. • When changing the temperature from a high setting to a low setting, allow approximately 5 minutes for the lower temperature to be reached. • When steam ironing, use long, slow passes over the fabric. This will allow the steam to penetrate the fabric while allowing the heat of the soleplate to dry out the moisture. • To iron linens, turn garment inside out. Be careful not to use an iron that is too hot because the lining may melt or stick to the soleplate. • To iron zippers, use an ironing cloth or make sure the zipper is closed and iron over the flap. Never iron directly over an unprotected zipper. • Use the Ironing Guide to select the best setting and method for the fabric you plan to iron. • SUNBEAM® irons are designed to be used with ordinary tap water. In areas where hard water exists, Sunbeam recommends running one to two iron water tanks full of distilled water every month. Using distilled water on a monthly basis will help to prevent mineral build up. CAUTION: Do not overuse distilled water. It may cause the iron to drip or spit if it is used too often. REMPLISSAGE DU RESERVOIR 1. Assurez-vous que le fer soit debranche. Reglez le levier de vapeur a « /Off» (repassage a sec) et le cadran de selection des textiles a «OFF». 2. Levez le volet de l’orifice de remplissage. 3. Remplissez le godet d’eau puis versez l’eau dans le reservoir du fer. Ne remplissez pas le reservoir au-dela du repere MAX de remplissage. AVERTISSEMENT: Remplissez tres prudement le reservoir d’un fer chaud. Les pieces en metal chaudes, l’eau chaude et la vapeur peuvent causer des brulures. REPASSAGE A SEC 1. Assurez-vous que le levier de vapeur soit au reglage « /Off» (repassage a sec). 2. Branchez le cordon d’alimentation sur courant alternatif de 120 volts. 3. Reglez le cadran de selection des textiles au tissu voulu. Laissez chauffer le fer pendant 2 minutes. Tandis que le fer chauffe, assurez-vous qu’il repose solidement sur son talon d’appui et qu’il soit pose sur une surface stable et protegee. REMARQUE : Bien que le levier de vapeur soit au reglage « /Off» (repassage a sec), vous pouvez quand meme utiliser le jet de vapeur SHOT OF STEAM® ou l’atomisation SPRAY MIST®, a condition que le textile soit regle a «Wool» (laine), «Cotton» (coton) ou «Linen» (lin) et que le reservoi...

Herunterladen

Geben Sie zwei Ziffern: