Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
• Poor phone line conditions • No “handshake” signals from remote fax • Document misfeed or miscount • Unable to reach remote machine after attempting specified number of redial tries Line is busy. • Remote machine’s line was busy • Remote machine’s line didn’t answer Check received documents. • Remote confirmation signal not received from remote fax • Poor line conditions caused a poor image Memory full. • Remote fax’s memory is full Dialing number is not set. • Stored phone number failed to dial properly Stopped. • Someone pressed STOP at the remote fax in the middle of the “handshake” Caring With proper installation and a little your fax machine should give you dependable service for years to come. Although it requires little day-to-day care, you can take these simple precautions to keep it in top form: • Always make sure your fax machine is installed according to our specifications, including using an electrical surge suppressor. (If necessary, review “Pick an installation spot, ” page 1.5.) • Always use good, copier-quality paper. • Always clean your fax machine as needed (see “Cleaning tips, ” below). • Never install your fax machine where it can overheat, gather dust or get splashed by any liquids (even water). Cleaning tips Some things to keep in mind about cleaning your fax machine: • Clean it! Dust and dirt, especially around the fax machine’s air vents can shorten your machine’s life. • Always unplug the fax machine before you clean it. • Never spray any cleaner DIRECTLY onto your fax machine. The drifting spray could damage components inside. • Never try to clean SEALED areas inside your fax machine. They’re sealed to protect your safety and the machine. • For cleaning external surfaces, such as the cover and handset: use a mild cleaning solution sprayed onto a lint-free towel or cloth. • Always use a lint-free cloth (or swabs) moistened with alcohol to gently wipe components inside your machine. • In areas you can’t reach with swabs, always use dry, dust-free compressed air to gently blow away dust and other material. Just in case … Corrective cleaning Here are some simple cleaning procedures for keeping your fax operating smoothly. Use each as the need arises. Curing frequent jams in the ADF If you’re having trouble with getting your original documents to try this procedure: 1 Turn off your fax machine. 2 Get two soft, lint-free cloths and moisten them as follows: • One with a cleaner suitable for use on platen/rubber rollers. In steps 4 and 6, we’ll call this the rollers cleaner. • The other with isopropyl alcohol 3 Open the scanner cover by holding the scanner cover release. Important: You must hold the cover open. It won’t stay open by itself. 4 Use the cloth with the rollers cleaner to clean the face of the rollers. Rotate the rollers by hand to allow cleaning of the entire roller surface. Just in case … 5 Open the inner cover fully. Important: You must hold the cover open. It won’t stay open by itself. 6 Use the cloth with the rollers cleaner to clean the face of the rollers. Rotate the rollers by hand to allow cleaning of the entire roller surface. Cleaning the LED print head If you find your fax recipients complaining that the faxes you receive or copy image quality are streaked, the LED print head may be dirty. Important: Be careful not to put your hand between the top cover and the machine. 1 Turn off your fax machine. 2 Get a soft, lint-free cloth and moisten it with isopropyl alcohol. 3 Open the top cover and then open the printer cover. CAUTION: The fuser unit becomes very hot. Do not touch the fuser unit when you are cleaning the LED print head. 4 Using the cloth, gently clean the LED print head. Note: Do not use abrasive materials on the LED print head, and do not subject the LED print head to strongly shock. If you have unsatisfactory printout quality Your machine automatically cleans its charger and transport roller, two items which are very important to printout quality. So, if you notice poor printout quality (whether on received faxes or on copies), it may mean that your machine requires service. Review “Print quality problems” (pages 5.3-5.4), and see whether any of the proposed solutions helps your machine. If none do, please call your authorized Muratec dealer or call the Muratec Customer Support Center at (800) 347-3296 (from the U.S. only). 5.12 Common s We’re here to help you! The Muratec Information System is available to you 24 hours a day, 7 days a week. You can use your fax machine to call this “fax-on-demand” system and receive printouts of information, such as the most common questions asked about your machine. Often, this is the fastest way to find out the answer to any question you may have. And it’s a free call! To use the Muratec Information System: 1 On your fax machine, press MONITOR/ CALL to get a dial tone, or lift your optional handset. 2 Call 1-800-215-1698. 3 Follow the voice instructions you’ll receive from the system. General questions Q: Where do I ...