Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Switch frequency channels to prevent interference from other RF pointing devices. (See the following section for more information.) - 2 - PDF ... "FinePrint pdfFactory Pro" ..... Wireless Optical Zoom Mouse Selecting the Frequency Channel The RF-Mouse operates on two frequency channels. To prevent interference when using two RF Mice in close proximity, a different frequency channel should be used for each mouse. Refer to the following instructions to change the frequency channel for your mouse: 1. Set the frequency channel (B) on the receiver to 1 or 2. 2. Remove the battery cover from the mouse (see the following Inserting the Batteries section). 3. Set the frequency channel (L) on the mouse to 1 or 2. (The frequency channel for mouse and receiver must be the same). Inserting the Batteries The RF-Mouse uses two batteries. Refer to the following to insert the batteries: 1. Press the tab on the bottom of the mouse cover as shown here and remove the cover. 2. Insert the two batteries. (The correct polarity is indicated on the battery compartment casing.) 3. Replace the cover. LL B - 3 - PDF ... "FinePrint pdfFactory Pro" ..... Wireless Optical Zoom Mouse Receiver works as a charger The receiver can work as a charger which you can put the spare rechargeable batteries on the charging compartment. The LED (K) light shows you that the mouse is working properly. The LED (M) is the charging LED. The bright charging red light shows you that the batteries are low. The light turns to dim as the batteries are charged for some time. When the light turns off, it implies the battery power is fully charged. *. DON’T CHARGE NON-RECHARGEABLE BATTERY TO THIS RECEIVER. About the indicating light (LED) on receiver 1. When using the mouse, the left working light(K) is blinking and in Green. 2. If the rechargeable batteries are charged, the left LED(M) is in red. The bright red light(M) shows you that batteries are low. 3. The light(M) turns to dim as the batteries are charged for some time. When the light(M) turns off, it implies the battery power is fully charged. K M - 4 - PDF ... "FinePrint pdfFactory Pro" ..... Wireless Optical Zoom Mouse Installing the iZoomWorks Software If there’re other mouse drivers installed on your computer, please have them uninstalled before you start the installation process. Also please be sure you have completed above hardware setup. Windows 95/98/ME/2000/XP/NT4.0 installation (Note: the USB Device does not support Windows 95/NT4.0) 1. Connect the mouse to your computer. 2. Insert the installation diskette into your floppy disk drive. 3. Click the Start button and then click Run. 4. In the Run dialog window, type A:\setup, where “A” is the letter of your floppy disk drive. 5. Click OK and follow the instructions on your screen to complete the installation. Checking the Batteries power To check the battery power, right-click the mouse icon in the System Tray. Choose the “Check RF-Mouse Status” option to display the RF-Mouse Status window. The current battery remain power percentage is shown. Power On/Off switch A power On/Off switch (N) is located on the bottom side as shown. You may turn off the power when it’s not in use. It saves battery power and prolongs battery life, which is convenient for traveling. N - 5 - PDF ... "FinePrint pdfFactory Pro" ..... Wireless Optical Zoom Mouse The RF-Mouse ID code Each RF-Mouse is assigned a unique ID code at manufacture, so the receiver only picks up the signal from your mouse and prevents other RF-Mouse radio signals from operating on your computer. This feature can also be disabled, allowing other RF-pointing devices to operate your computer. Connecting the RF-Mouse ID Code When the driver installation is finished your computer reboots and the RF-Mouse window (shown on the right) appears. Before setting up the RF-Mouse ID connection, please make sure there are no other RF pointing devices around and in use. CONNECT ID: Move the RF-Mouse for a few seconds to establish a connection, and then click Connect ID. The unique ID code of your mouse is recognized. Once this process properly executed, other RF pointing devices will not function on your computer. Exit: Click Exit to complete the ID setup. Changing the RF-Mouse ID Code You can use a new RF-Mouse on your computer without changing the Radio receiver; you just need to change the ID code. Refer to the following: 1. Press [Shift + Alt + F11] or [Shift + Alt + F12] to call up the RF-Mouse ID Code window. 2. Move the RF-Mouse for a few seconds to establish a connection, and then click Connect ID. 3. The new ID code is connected and the RF-Mouse window closes. Click Exit to close the RF-Mouse ID code window. - 6 - PDF ... "FinePrint pdfFactory Pro" ..... Wireless Optical Zoom Mouse The 4th & 5th Buttons:The 4th and 5th buttons work as zoom in and zoom out and are programmable with ...