Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 8.25 mb Dateiname: Unterrichtssprache:

Insert the new cartridge into the TV in the same orientation as the old cartridge. Push on the cartridge housing until it is fully seated. 8. With either your fingers or the screwdriver, gently tighten the three screws. If using a screwdriver, use only two fingers for final tightening. AVOID OVERTIGHTENING! 9. Replace the plastic grille/cover and retaining screws. 10. WASH YOUR HANDS THOROUGHLY, AS THIS LAMP CONTAINS MERCURY. 11. Contact your local authorities or the Electronic Industries Alliance at for lampdisposal or recycling instructions. Do not dispose of the old lamp with common trash. 12. Reset the Lamp Reminder from the TV Setup menu as follows: a. Press TV MENU to open the Setup menu. b. Move the highlight to Lamp Reminder. c. Press ENTER twice. Figure 1. Figure 2. Handle Figure 3. Appendix H: Diamond Shield Removal and Installation The Diamond Shield ™ is an optional protective cover for the front of the TV screen. Models WD-62927 and WD-73927 come from the factory with the Diamond Shield installed. For Models WD-62827 and 73827, the Diamond Shield may be purchased separately. These instructions explain removal and installation of the Diamond Shield™ and the decorative trim that covers gaps around the TV screen when the shield not installed. You need the following for this procedure: Trim kit (included with the TV) Phillips screwdriver Small plastic card or plastic putty knife. An expired credit card or similar expendable card works well. Soft cotton gloves Note: Use care to avoid scratching the TV screen or Diamond Shield. This procedure is best performed by two people. Remove the Shield 1. Using a Phillips screwdriver, remove the screws that secure the top plate and lift off the plate. Keep the plate and screws for reuse. See figure 1. Figure 1. Remove the screws securing the top plate and lift off the plate. Top Plate 2. Note the location of the six clips that hold the Diamond Shield in place. Slide the card along the channel until it meets each clip. See figures 2 and 3. See figure 3 detail Figure 2. Six clips hold the Diamond Shield on the TV. Diamond Shield Slide card in channel to locate clips. The clips are visible at the edge of the Diamond Shield. Figure 3. Locating the clips Appendix H: Diamond Shield Removal and Installation, continued 3. Release the six clips that hold the Diamond Shield in place. Work on one side at a time, starting with the top clip. Follow these steps: (1) Refer to figure 4. Hold the plastic card vertically, angled slightly toward the middle of the screen. (2) Insert the card into the channel, alongside the clip. (3) Refer to figure 5. While keeping the card pressed in on the clip, angle the card outward, away from the middle of the screen, and pry out the clip. WARNING Sharp edges! Always wear gloves to handle, lift, install, and remove the Diamond shield. 4. When all clips are released, lift the shield up out of the lower channel and away from the TV. 5. Store the Diamond Shield protected from scratches in a clean, dust-free area. Notched edge down Figure 6. Center the trim piece, notched side down, and set it in the channel below the screen. TV Screen Raised Lip Trim Piece Channel Figure 7. The lower trim piece fits snugly into the channel and over the raised lip that runs along the bottom of the TV screen. Diamond Shield Angle card toward shield before inserting Top View Note Angle of Card Figure 4. To release the clip, insert the card alongside the clip at the angle shown. Figure 5. Pry the clip out of the channel. Clip Top View Install Trim Note: Install the trim pieces in the order described here. 6. Install the lower trim piece as follows: (1) Center the trim piece in front of the TV, notched edge down, and set it in the channel below the screen. See figure 6. (2) Refer to figure 7. With the trim piece resting in the channel, hook the trim piece onto the raised lip at the bottom edge of the TV screen. To do this, a. Gently press the trim piece against the TV frame. b. Push the trim up slightly to clear the raised lip. c. Press down firmly on the top edge of the trim piece to push it snugly into place over the raised lip and into the channel. Be sure to press along the entire length of the trim to fully seat it. Appendix H: Diamond Shield Removal and Installation, continued 7. Refer to figure 8 and install the two side-trim pieces as follows: (1) Hook the lower end of the trim over the raised lip running down the side of the TV screen. (2) While keeping the end of the trim hooked on the raised lip, slide the trim down until it meets the lower trim piece. (3) Hold the bottom end of the trim in place and hook the top end on the raised lip that runs along the top edge of the screen. (4) Push the top end of the trim up against the edge of the screen. Press the full length of the trim onto the raised lip. (5) Press the outer edge of the trim so that the entire length snaps into place. Figure 8. Hook the ends of the trim piece over the raised lip at ...

Herunterladen

Geben Sie zwei Ziffern: