Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
-8236 Specifications . Height - 68 inches . Length - 79 inches . Width - 62 inches . Weight - 120 lbs. p/n 108236 Instruction No. 101914 - Clam Customer Service Information - NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE A WARRANTY CLAIM, PLEASE CONTACT CLAM CORP. CUSTOMER SERVICE BY EMAIL INQUIREY OR DIRECT BY CALLING: . .. Clam Corporation, Inc. 600 Clydesdale Trail Medina, MN 55340 .. Phone - 763-231-4120 .. Fax - 763-231-4121 .. Email – customerservice@clamcorp.com .. Website – Customer Service Hrs: - 9am to 4pm, Mon. - Fri. Central Standard Time - Bill of Materials -- Bill of Materials - ITEM QTY P/N DESCRIPTION ITEM QTY P/N DESCRIPTION 1 4 101048 BLOCK, SLIDE 17 1 101811 BASE, MEDIUM XTR 2 18 101081 WASHER, 1/4" FLAT 18 2 101813 BRKT, RAIL HANGER 3 26 101082 LOCKNUT, 1/4" THIN 19 1 101817 BRKT, FRONT SEAT 4 8 101088 SCREW, 1/4-20 X 0.75 PHILLIPS 20 6 101829 POLE ASSY, STRAIGHT POLE 5 2 101146 ANGLE, 9" LONG ALUMINUM ANGLE 21 2 101830 POLE ASSY, BENT CANOPY 6 4 101147 SCREW, #10 X 1" LONG PHILLIPS 22 2 101836 POLE ASSY, FRONT SPREADER 7 1 101399 PLATE, 6" SQUARE SWIVEL 23 1 101840 POLE ASSY, REAR SPREADER 8 1 101424 BRKT, REAR SEAT 24 1 101842 TENT, X 9 4 101429 CAP, 1-1/8" TUBE 25 4 101862 POLE ASSY, CANOPY HOOP 10 1 101442 CLIP, LATCH 26 2 101864 POLE ASSY, ROOF SPREADER 11 1 101466 HAMMOCK, CLOTH ACCESSORY 27 1 101905 SEAT ASSY, TWO-TONE 12 8 101470 BOLT, 1/4" DIA HEX HEAD BOLT X 1/2" 28 8 101906 SCREW, 1/4" DIA X 2-1/2" PHILLIPS 13 2 101473 SCREW, 1/4" DIA X 1-1/2" PHILLIPS 29 1 101907 TUBE, MED XTR SEAT RAIL 14 4 101486 SCREW, 1/4" DIA X 1-3/4" PHILLIPS 30 1 101909 MOLDING, U-CHANNEL 15 2 101652 TUBE, 1-1/8" DIA 31 20 101938 SCREW, #8 PHILLIPS 16 2 101810 BRKT, XTR CANOPY - Seat Parts Diagram (See pg. 4 for Assembly) - 2 - Shelter Parts Diagram (See pg. 4 for Assembly) -- Shelter Parts Diagram (See pg. 4 for Assembly) - - Step 0ne -- Step 0ne - - Step Two -- Step Two - - Step Three -- Step Three - - Step Four -- Step Four - - Step Five -- Step Five - - Step Six -- Step Six - - Step Seven -- Step Seven - - Step Eight -- Step Eight - - Step Nine -- Step Nine - - Step Ten -- Step Ten - Angle the Seat Assembly slightly while placing the bottom lip of the Front Seat Bracket under the Angle the Seat Assembly slightly while placing the bottom lip of the Front Seat Bracket under the - Seating Installation - outside edge of the Base Lip. With the Latch Clip hanging freely, tilt the complete assembly downward until the interior of the Rear Seat Bracket surrounds the Support Tube. 14 - Seating Installation (cont.) - Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up against the underside of the Support Tube. Squeeze the Latch Clip into the horizontal slot of the Rear Seat Bracket. Secure the position of the Latch Clip by pushing it into the two holes located above the horizontal slot of the Rear Seat Bracket. WARNING: ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE. FAILURE TO DO SO COULD RESULT IN INJURY FROM THE SEAT COMING OFF OF ITS MOUNTING SYSTEM. Included is a Tow Rope for those not planning to install the optional Tow Hitch Assembly (available for purchase at Two install the Tow Rope, drill two 1/2" holes in the sloped front of the Base. Knot the ends of the Tow Rope after routing through the drilled holes. - Seating Installation (cont.) - Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up against the underside of the Support Tube. Squeeze the Latch Clip into the horizontal slot of the Rear Seat Bracket. Secure the position of the Latch Clip by pushing it into the two holes located above the horizontal slot of the Rear Seat Bracket. WARNING: ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE. FAILURE TO DO SO COULD RESULT IN INJURY FROM THE SEAT COMING OFF OF ITS MOUNTING SYSTEM. Included is a Tow Rope for those not planning to install the optional Tow Hitch Assembly (available for purchase at Two install the Tow Rope, drill two 1/2" holes in the sloped front of the Base. Knot the ends of the Tow Rope after routing through the drilled holes. 15 - Safety Instructions - - Safety Instructions - Please fully understand and follow all safety instructions as outlined. Failure to do so could result in severe injury or death. ..Do not use open flame heaters in your ice shelter. Injury or death may result from fire if tent fabric is exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that meets CPAI-84 specifications. Application of any foreign substance may render the flame retardant properties ineffective. Ice Armor fabric will melt when contact is made with hot surfaces (i.e., heaters). ..Death from asphyxiation may result from use of oxygen depleting heaters. Open all vents for fresh air ventilation. ..Never leave shelter unattended when set up. ..Due to the increase in traffic (snowmobile...