Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Please contact Brunton at the number below to obtain RA#. Clean food and soot from stove before shipping. Shipping cost to Brunton is the responsibility of the purchaser. Return postage will be paid by Brunton. Please return this warranty card to Brunton as a proof of purchase. This warranty does not cover damage caused by accident, misuse, abuse, or tampering. A nominal charge will be assessed to repair such damage. Brunton assumes no responsibility for any inconvenience, loss, or injury, direct or consequential damage arising from possession or use of the goods. This warranty gives you specific legal rights which may vary from state to state. Check with your local state about your rights. LIMITS OF LIABILITY BANTAMTM Please read, understand and follow all instructions and warnings before using this product. The proper fuel bottle for this product is included. BRUNTON ATTN: WARRANTY DEPT. 2255 BRUNTON COURT RIVERTON, WYOMING 82501 307.857.4700 BRUNTON WARRANTY REGISTRATION NAME_______________________________________________________ ADDRESS___________________________________________________ CITY_________________________ST/PROV_______ZIP__________ PHONE _______________________EMAIL_______________________ MODEL#__________________DATE PURCHASED____________ PURCHASED FROM_______________________________________ CITY_________________________ST/PROV_______ZIP__________ PRICE PAID $___________________ 1006 VISIT OUR WEBSITE AT Warranty card must be filled out completely and returned within 30 days with proof of purchase for warranty to be valid. - Before using the Brunton Bantam stove, please read and follow all the steps below carefully. 1. Pour the fuel up to the fill line on the bottle. Do not overfill. 2. Insert pump and turn clockwise to tighten. To avoid the possibility of serious injury, use only a Brunton pump and bottle. Use only White Gasoline, other fuel could clog the nozzle and may cause a fire hazard. Keep away from children. Filling the fuel bottle OPERATING INSTRUCTIONS Using the stove on uneven surface is very dangerous and may cause a fire hazard and serious injury. When the fuel bottle has been connected to the pump be sure that the valve knob is set to the OFF position. When the stove is in use, keep fuel bottle as far away as possible. Using the stove Preheating the stove - Before using the stove with white gas, it is necessary to pre-heat the fuel. This is called priming the stove. 1. Turn the valve knob counter clockwise to the (ON) position and wait 1-2 seconds until the jet emits a small amount of fuel onto the priming pad then close the valve by rotating the knob counter clockwise to the (OFF) Position. If fuel does not flow, the fuel bottle is low on gas and the bottle may need preasurizing or more fuel. 2. After connecting the flexible hose to the pump, ensure that the fuel bottle is placed on a flat surface. 1. Unfold the stove legs and place the stove on a flat surface. 2. After the fire extinguishes, the stove will remain hot, wait until the stove cools down. 3. Separate the stove from pump. 4. Fuel bottle and pump can be transported as a connected assembl y y. When separating the pump from fuel bottle, turn the pump slowly so that the pressure retained inside the fuel bottle can release gradually. 1. To extinguish the stove, turn the valve knob to the OFF position and flip the bottle over. NOTE: The stove will continue to burn for a short time until all of the fuel in the generator tube and fuel hose is consumed. Turn slowly counterclockwise after preheating Flip Small flame remains for 2-3 minutes consuming all the fuel in the hose. Dried or torn parts need to be replaced. Check the color and size and any printed markings and contact your nearest Brunton stock list or retailer for replacements. (Oil seals, Oil, Nozzle, Tool kit) Poor performance & nozzle clogging - Colgging inside the nozzle or generator tube may disturb the fuel and create poor stove performance. - Remove clogging inside the nozzle hole with a nozzle pin. - If clogging persists inside of the nozzle or generator tube, a more thorough cleaning is required. A) How to clean with nozzle pin 1. Turn off the stove valve and wait until the stove has completely cooled down. 2. Remove the Jet by disassembling and removing the generator tube assembly from the stove with the tool kit. 3. Clean the jet with the nozzle pin 4. Re-Assemble the stove and check for any fuel leaks. - If cleaning the Jet does not improve the stove efficiency, clean the generator tube as well. B) How to clean the generator tube 1. Begin by removing the generator tube assembly from the stove with the tool kit. 2. Pull the wire out brush clean of any debris and replace 3 . Re-Assemble the stove and check for any fuel leaks leg A o-ring leg B leg pin fill line 20-30 times head oil plate leg B guide spring guide nozzle connect nut nozzle connect bolt o-rings pump knob hose cap hose nozzle connect nozzle body nut hose washer ...