Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
• Consult the dealer or an experienced radio/TV technician for help. Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. For countries outside the United States: CANADA: Questions? 1-800-432-5437. Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2; GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303; AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. NEW ZEALAND: 16-18 William Pickering Drive, Albany 1331, Auckland. ASIA: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. ©2006 ESPN, Inc. All Rights Reserved. Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. ©2006 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO 2 K9125pr-0920 Par ParParts tsts 4 5 6 Collar Backboard Ball Rim Lower Post Upper Post Plug Base Note: Label not shown Hint: Some parts were placed inside the lower post for shipping. Sound Box Paddle BOTH SHOWN ACTUAL SIZE Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten. #6 x 3/4" (1.9 cm) Screw - 4 #8 x 2 1/4" (5.7 cm) Screw - 1 3 Assembly AssemblyAssembly Side Edge 43 1 2 Proper label application will help to keep the label looking its best! • Make sure the area where the label will be applied is clean and dry. Wipe the backboard with a clean, soft, dry cloth to remove any dust or oils. • For best results, avoid applying the label more than once. • Peel the backing from one half of the label. Do not remove all of the backing! • Align the side edge of label 1 (where backing is removed) with the side edge of the label area on the backboard. • Carefully apply the side edge of the label to the side edge of the label area on the backboard. • While rubbing the label in place, continue to peel the backing from the other half of the label. • Apply the remaining labels to the backboard. Labels 1 - 4 are designed to overlap. • Dispose of the label backing properly. 7 15 6 • Position the base as shown. • Position the upper post so that the straight end is down and the curved end is up and facing away from the base. Hint: For easier assembly, apply liquid soap or rub a candle or bar soap around the bottom of the upper post (especially on the corners) and the inside of the large square opening. If assembling inside, place a tarp under the base to protect the floor surface. • Insert the upper post into the large square opening in the base and, using a circular motion, push it all the way down. 4 5 6 Large Square Opening Base Upper Post Curved End 34 5 6 Rectangular Tab Rim Upper Post 4 • Hook the rectangular tab on each side of the rim to the upper post, as shown. • Rotate the rim down until it snaps into place on the upper post. Push down on the rim to be sure it is secure. Plug“T” EndBase 2 • Bend the “T” end of the plug and insert it into the hole in the base. Note: After assembly is complete, fill the base with water or approximately 50 lbs. (22.7 kg) of sand (water and sand not included) to keep this product stationary. Simply lift the plug, fill the base, and replace the plug. 4 Assembly AssemblyAssembly 6 4 5 Backboard Labels Peg Groove Wall Rim Upper Post • Lean the rim against a wall for support. • Locate the pegs on each side of the rim and the grooves on the backboard. • Position the backboard with the label side facing up. • Place your foot on the base to hold it steady and slide the backboard onto the upper post at an angle, as far as it will go. Note: There should be no gap between the upper post and the backboard. • Move the assembly away from the wall. 5PULL HERE PRESS HERE Top View • Move to the side of the assembly. • Place your foot on the base to hold it steady. • Press down firmly on the lower backboard while rotating the backboard up. Paddle Soundbox • Fit the paddle onto the pegs on the soundbox, as shown. • Insert the #8 x 2 1/4 screw through the paddle and into the soundbox and tighten. 6Back View Peg Peg Grooves 7• Fit the soundbox to the underside of the rim and hold it in place. • Insert four #6 x 3/4" screws into the soundbox and tighten to secure it to the rim. 6 4 5 Rim 8Soundbox • When properly assembled, the pegs on the upper post rest in the grooves in the backboard, as shown. Note: The height of the rim is three feet (1 m) as assembled. 5 Assembly AssemblyAssembly 6 4 5 Lower Post Rib Base 9Groove IMPORTANT! Assembly of the lower post to the base is a permanent assembly. • Align the rib on the bottom of the lower post with the groove in the opening in the base. Hint: For easier assembly, apply a small amount of liquid soap around the bottom of the post. If assembling indoors, ...