Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Press SQUARE PLUG (55) into the top of the REAR UPRIGHT (3). ?] Press FOUR 2"SQUARE CAPS (53) onto the end of the BASE TUBES ( as shown) in drawing. G\ Attach FOOT PLATE (17) to MAIN BASE FRAME (1) and insert "L" PIN (76) into the hole of the FOOT PLATE (17) and MAIN BASE FRAME (1). Press 2" SQUARE PLUG (77) into the end of the MAIN BASE FRAME (I) (as shown) in drawing. UPRIGHT ASSEMBLY TOP FRAME ASSEMBLY Attach TOP FRAME (7) to FRONT UPRJGHT (5). using 2- 3/8" x 3" BOLTS 4- 3/8" WASHERS 2- 3/8" NYLON NUTS Tighten bolts firmly. IT] Attach TOP FRAME (7) to REAR UPRJGHT (3), using FLAT BRACKET (22) 2- 3/8" x 2 3/4" BOLTS 4- 3/8" WASHERS 2- 3/8" NYLON NUTS Push two METAL BUSHINGS (52) into holes on each side of the TOP FRAME. J I I 7 SUPPORT ASSEMBLY I A Attach SUPPORT TUBE (9) to FRONT UPRIGHT (5) using, 2- 3/8” x 3 “ BOLTS 4- 3/8” WASHERS 2 -3/8” NYLON NUTS then insert SQUARE PLUG (56) into each end of SUPPORT TUBE.. I] Place 3/8” x 1” BOLT into BUMPER (63) and screw tight into SUPPORT TUBE (as shown). Attach 15.8 x 10 x 2.3 HEX BOLT (12) to the bracket of the SUPPORT TUBE (9) using, 1- 5/16” x 1 7/8” BOLT 2- 5/16” WASHERS 1-5/16” NYLON NUT. C Attach BACKREST PAD (20) to FRONT UPRIGHT using, 2- 3/8" x 2 3/8" BOLTS 2- 3/8" WASHERS. Attach PRESS SUPPORT (10) onto the TOP FRAME (7) using 1/2" x 7" PIVOT BOLT (38) 2- 1/2" WASHERS 2- 1/2" NYLON NUTS Tighten BOLTS firmly. Push 2 - 38 x 38 SQUARE PLUGS (56) and 2- 45 x 45 SQUARE PLUGS (55) into the four sides of the PRESS SUPPORT (10). Push 4 METAL BUSHINGS (52) into the holes on the PRESS SUPPORT (10) (as shown) and attach the THREADED BOLTS of the PRESS/PECDEC ARM (11) into the METAL BUSHINGS (52) of the PRESS SUPPORT (10). Use 2- 1/2" NYLON NUTS and 2- 1/2" WASHERS. D Press two BIG FOAM ROLLER (67) onto the PRESS/PECDEC ARM (11), attach HAND TUBE (14) to PRESS/PECDEC ARM (11) using 2- 5/16" x 2 1/8" bolts 4- 5/16" WASHERS 2- 5/16" NYLON NUTS on each side. Then push 2 - 38 x 38 SQUARE PLUGS (56) and 2-31.8 ROUND PLUGS (58) into the end of BAR and PRESS/PECDEC ARM (11). 10 CABLE INSTALATION 11 ASSEMBLY C Attach CABLE (71) to PRESS/ PECDEC ARM (11) using. 1-3.'8" x 1" BOLT 2- 3/8" WASHERS 1- 3. 8” NUT tighten BOLT firmly. D Hook Cable (72) to COLLEC I ION HOOK (68) (as shown). (4 Attach two PULLEYS (61) into the PULLEY BRACKET of the TOP FRAME (7), AND TWO PRLLEYS(6I) into the PULLEY BRACKET of the PRESS SUPORT (10) (as shown) using. 1-3/8" x 2" BOLT 2- 3/8" WASHERS 1-3/8" NUT on each BRACKET. Attach PULLEY (61) into the hole on the FRON1 UPRIGHT using 1-3/8" x 2 5/8" BOLT 2- 12.7 X 1.0 X 10 METER SPACER 2- 3/8" WASHERS 1-3/8” NYLON NUT Slide HAND GRIPS (59) on to each side of LAT BAR (16). ASSEMBLY A Attach two PULLEYS (61) into the DOUBLE BRACKET (23) and two PULLEYS (61) into the OFFSET BRACKET (24) using 1- 3/8” x 2" BOLT 2- 3/8” WASHERS 1- 3/8” NYLON NUT on each PULLEY. B Attach PULLEY (61) to BRACKET of the MAIN BASE FRAME (1) using 1-3/8" x 2" BOLT 2- 3/8"WASHERS I-3/8" NYLON NUT Attach PULLEY (61) to BRACKET of the FRONT UPRIGHT using "L" BRACKET (21) 1- 3/8" X 2 1/4" BOLT 2-3/8" WASHERS 1-3/8" NYLON NUT. Attach PULLEY (61) into hole of the FRONT UPRIGHT using 2- METAL SPACERS 1-3/8" X 2 5/8" BOLT 2- 3/8" WASHERS 1-3/8" NYLON NUT Attach PULLEY (61) into LEG EXTENTION TUBE (13) using 2- 12.7 x 1.0 x 7.5 METAL SPACERS 2-3/8" X 2 3/8" BOLT 4- 38" WASHERS 2- 3/8" NYLON NUT Attach one HAND GRIP (59) on each side of CURL BAR (18). FIRMLY TIGHTEN EVERY NUT AND BOLT ON WEIGHT MACHINE!!! ST—150(REVISED) USING 3/8"*3" BOLT USING 3/8"*3(3/8)" BOLT (INSTEAD OF 3/8"*3" BOLT) USING 3/8M*2(3/4)" BOLT...