Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Secure bottom pole (7) to tank and wheel bracket as shown, a deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 3. 9 8 7Install rod (8) through holes in bottom pole section (7) and eyebolt (9). THE SPACER (11) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE IMPORTANT!: 12 7 8 9 2 11 11 3 3 10 Install wheel axle (2) through wheel carriage (10). Install wheels (3) onto wheel axle (2) with spacers (11) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (7) to tank and wheel bracket as shown, a deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 3. 9 8 7Install rod (8) through holes in bottom pole section (7) and eyebolt (9). THE SPACER (11) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE IMPORTANT!: 12 P/N 211696 07/03 Attach middle section of pole (6) onto bottom section of pole (7). Align holes in middle pole (6) with hole pattern on bottom pole (7). Secure struts (15) to poles by using bolt (17) & Item #21 (2) 17 sleeve nut (16) with supplied allen wrench (21) as shown. 16 15 13 07/03 P/N 211696 5. 6 7 6. 7. 7. Secure poles by attaching bolt (17), washers (14), and sleeve nuts (16) as shown. 7 6 16 17 14 14 14 P/N 211696 07/03 Rotate the non-secured ends of base struts (15) as shown. Secure base struts (15) to base using bolts (18), washers (19), and 15 8. nuts (20). 18 19 20 18 20 19 19 15 07/03 P/N 211696 9. 9. Support pole on sawhorse. Attach upper section of pole (5) to middle section of pole (6) using bolts (17), washers (14), and nuts (16) as shown. 17 6 5 17 14 16 14 16 14 14 16 P/N 211696 07/03 10. 10. While still supported on sawhorse attach top section of pole (4) to upper section of pole (5) using bolts (17), washers (14), and nuts (16) as shown. 6 14 14 16 17 17 14 4 5 16 14 17 07/03 P/N 211696 SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) 3/4", 9/16” and 1/2” 3/4", 9/16” and 1/2” AND/OR Item #23 Item #18 Item #20 Item #34 Item #24 Item #32 Item #29 Item #26 Item #30 Item #33 Item #11 Item #36 Item #22 Item #42 Item #40 Item #37 Item #43 Item #41 18 P/N 211696 07/03 1. 1. Assemble backboard brackets (25) using spacers (22), bolts (24), and nuts (23) as shown. 22 22 24 24 23 23 25 19 07/03 P/N 211696 2. 23 24 2726 Fit spacer (26) into pawl (27). Continue to assemble as shown. 3. 30 28 31 30 28 29 29 11 11 27 32 32 25 IMPORTANT! Test-fit bolts into holes of backboard brackets (25) and carefully rock them in a circular motion to ream out paint from holes if necessary. Attach lower elevator tubes (28) to backboard brackets (25) using spacers (29 & 11), bolts (30) spacers (11) ratchet (31), and nuts (32) as shown. 20 P/N 211696 07/03 07/03 P/N 21169621 28 36 20 18 37 25 4. 33 34 27 34 27 35 5. 6. Secure pawl (27) in place with clevis pin (33) and washers (34). Stretch spring (35) into position with pliers. Insert “T” bolt (36) through Slam Jam bracket (37) as shown. Secure Slam Jam bracket (37) to backboard using bolt (18) and nut (20) as shown. USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 28 36 20 18 37 25 4. 33 34 27 34 27 35 5. 6. Secure pawl (27) in place with clevis pin (33) and washers (34). Stretch spring (35) into position with pliers. Insert “T” bolt (36) through Slam Jam bracket (37) as shown. Secure Slam Jam bracket (37) to backboard using bolt (18) and nut (20) as shown. USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 30 29 29 32 28 28 7. 28 28 Attach upper elevator tubes (28) to backboard brackets (25) using spacers (29), bolt (30), and nut (32) as shown. 25 30 29 29 32 28 28 7. 28 28 Attach upper elevator tubes (28) to backboard brackets (25) using spacers (29), bolt (30), and nut (32) as shown. 25 8. 32 28 28 30 30 32 38 4 Support pole on sawhorse. Attach upper and lower elevator tubes (28) to top pole section (4) using bolts (30) and nuts (32) as shown. Attach pole cap (38) as shown. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 22 P/N 211696 07/03 40 39 37 36 40 39 37 36 Fit rim (39) securely into bracket (37) as shown. Install reinforcement bracket (40) onto “T” bolt (36) as shown. Install spring (41) onto “T” bolt (36) as shown. Install special nut (43) and washer (42) onto “T” bolt (36). Tighten nut (43) until flush with end of “T” bolt (36). 43 4...