Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Impex Dateigröße: 572.73 kb Dateiname: 0c95668f-e3a9-439b-aa2e-7814021e5d9c.pdf Unterrichtssprache:

Adjust the Upright (2) so that a bolt can be inserted through the center hole in each side. Secure the Upright with two M8 x 38mm Button Bolts (53) and two M8 Nylon Locknuts (50). 20 2 3 1 18 49 20 50 19 20 50 49 2 3 3 50 41 47 50 53 1 1 50 50 1 20 7 5. Identify the Left Pivot Arm (6), which is marked with a sticker that has an “L” on it. Make sure that there are two Pivot Bushings (9) in the Left Pivot Arm. Slide the Left Pivot Arm onto the Pivot Axle (11), making sure that it is oriented as shown. Put a Pivot Washer (54) onto an M8 x 19mm Button Screw (10) and tighten the Button Screw into the Pivot Axle. 6. Insert a Handlebar (12) into the Right Pivot Arm (7). Slide the Foam Grip (13) up to expose the mounting holes. Secure the Handlebar with two M5 x 30mm Button Bolts (51) and two M5 Nylon Locknuts (52). Slide the Foam Grip down over the Button Bolts and Nylon Locknuts. Attach the other Handlebar (12) to the Left Pivot Arm (6) in the same manner. 5 9 10 54 9 6 13 52 51 6 7 6 11 12 4. Make sure that the two Upright Bushings (8) are inserted into the Upright (2). Apply a thin film of the included grease along the length of the Pivot Axle (11). Insert the Pivot Axle into the Upright Bushings and the Upright. Identify the Right Pivot Arm (7), which is marked with a sticker that has an “R” on it. Make sure that there are two Pivot Bushings (9) in the Right Pivot Arm. Slide the Right Pivot Arm onto the Pivot Axle (11), making sure that it is oriented as shown. Put a Pivot Washer (54) onto an M8 x 19mm Button Screw (10) and tighten the Button Screw into the Pivot Axle. 4 9 8 8 2 11 7 10 9 54 Grease 8 10. Make sure that all parts of the elliptical glider are properly tightened. Place a mat under the elliptical glider to protect the floor or carpet from damage. 9 57 5 47 Console Wire 28 29 2 9. The Console (5) requires two “AA” batteries (not included). Alkaline batteries are recommended. To install batteries, look under the Console (5) and locate the battery compartment. Insert two batteries into the battery compartment; make sure that the batteries are turned so the negative ends (marked “–”) are touching the springs in the battery compartment. Connect the console wire to the Extension Wire (47). Attach the Console (5) to the Upright (2) with four M4 x 12mm Button Screws (57). Push the Resistance Knob (28) firmly onto the Resistance Cable (29). 8. Identify the Left Pedal Arm (14), which is marked with a sticker that has an “L” on it. Make sure that there are two Pedal Arm Bushings (33) in the Left Pedal Arm. Apply a thin film of the included grease to a Pedal Axle (34). Insert the Pedal Axle into the Left Pedal Arm, and slide a Pedal Washer (32) onto the Pedal Axle. Firmly tighten the Pedal Axle into the Crank (30). Tighten a 1/2” Nylon Locknut (35) onto the end of the Pedal Axle protruding from the Crank. Make sure that there are two Small Pivot Bushings (42) in the Left Pivot Arm (6). Apply a thin film of the included grease to an M8 x 60mm Bolt (...

Herunterladen

Geben Sie zwei Ziffern: