|
Anleitung Zusammenfassung
If the Wire Harnesses do not fit together easily, turn themNdo not force them together. Tip the Side Shields (55, 62) forward. If the three M10x 25mm Button Screws (49) and M10 Lock Washers (20) are in the Frame (1), remove them. Feed the Wire Harness (32) into the Frame, and slide the Upright (2) onto the Frame. Loosely thread the three M10 x 25mm Button Screws with M10 Lock Washers into the Upright and the Frame. After you have threaded all three Button Screws into the Upright and the Frame, firmly tighten them. Tip the Side Shields (55, 62) back and reattach them with the ten #8 x 1/2O Screws (25) removed in step 2. Install the bottom Screws first. 1. Feed the end of the console wire harness down through the Upright (2). Attach the Console (50) to the Upright with four #8 x 1/2O Screws (25). Be careful to avoid pinching the console wire harness. 4 Console Wire Harness 1 25 25 55 62 2 50 25 2 2 49 49 55,62 1 20 20 3 ASSEMBLY Assembly requires two people. Place all parts of the stepper in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY: The included allen wrench , a phillips screwdriver , and a rubber mallet . Console Wire Harness 32 4. Slide the Right Handlebar (10) onto the right side of the Upright (2). To keep the Handlebar from binding, slide both ends of the Handlebar on at the same time. While another person pulls back the upper end of the Foam Handgrip (57), loosely thread two #8 x 1/2O Screws (25) into the Right Handlebar and the Upright. If necessary, move the Right Handlebar slightly to align the holes in the Right Handlebar with the holes in the Upright. Next, pull back the lower end of the Foam Handgrip (57) and loosely thread two more #8 x 1/2O Screws (25) into the Right Handlebar and the Upright. Tighten all four #8 x 1/2O Screws (25). Attach the Left Handlebar (11) to the Upright (2) in the same manner. 5. If there are rubber bands on the ends of the 5/8O x 15O Rod (43), remove them. Slide a Wheel (44) onto one end of the Rod. Attach the Wheel with an M6 x 20mm Button Screw (45) and a 3/8O Flat Washer (46). Attach a Wheel (44) to the other end of the 5/8O x 15O Rod (43) in the same manner. Plug the Power Cord (30) into the jack on the front of the stepper. 10 11 57 25 25 2 4 30 44 43 46 45 5 6. Make sure that all parts of the stepper are properly tightened. To protect the floor or carpet from damage, place a mat under the stepper. HOW TO USE THE IMAGE. 7.0 STEPPER The stepper console offers a variety of features to help you get the most from your exercise. When the console is in the manual mode, the stepping speed can be changed with a touch of a button. As you exercise, four LED displays will provide continuous exercise feedback. The console also offers six workout programs. Each workout program is designed to change the stepping speed automatically as it guides you throug...
Dieses Handbuch ist für folgende Modelle:Kraftstationen - 831.285780 (356.56 kb)
Kraftstationen - 831.285780 (356.56 kb)
Kraftstationen - 831.285780 (356.56 kb)
Kraftstationen - 831.285780 (356.56 kb)