Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Keys Fitness Dateigröße: 351.81 kb Dateiname: a05aa929-3ee8-485e-96ec-f4ba78b3e072.pdf Unterrichtssprache:

until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is 831.285731. The serial number can be found on a decal attached to the 485E (see the front cover of this manual for the location of the decal). Before reading further, please look at the drawing below and familiarize yourself with the parts that are labeled. Resistance Knob FRONT BACKLEFT SIDE Pedal Arm Pedal Disk Side Shield Pedal Book Holder Upright Water Bottle Holder (Bottle not included) T-Handle Handlebar 4 PART IDENTIFICATION CHART Use the chart below to identify the small parts used in quantity needed for assembly. Note: Some small assembly. The number in parenthesis below each part parts may have been pre-attached for shipping. If is the key number of the part, from the PART LIST on a part is not in the parts bag, check to see if it has page 14. The number after the dash indicates the been pre-attached. 3/8" Nylon Locknut (29)N4 Pedal Arm Spacer (41)N3 #8 x 3/4" Round Head Screw (16)N10 Weld Spacer (49)N2 5/8O Axle Cap (57)N2 3/4O Axle Cap (43)N4 Pivot Bushing (56)N4 1/4" Black Nylon Locknut (55)N2 1/4O x 3/4O Screw (54)N2 Pedal Arm Bushing (42)N8 Handlebar Spacer (39)N2 5 ASSEMBLY Assembly requires two people. Place all parts of the PROFORM. 485E in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires a phillips screwdriver , two adjustable wrenches , and a rubber mallet . 1. Feed the console wire down through the Upright (3) as shown. While another person holds the Upright near the Frame (1), tie the console wire and the Sensor Wire (25) together as shown in drawing 1a. Next, connect the console wire to the Sensor Wire. Gently pull the Resistance Cable (26) and the console wire out of the top of the Upright (3) until there is no slack between the Upright and the Frame (1). Slide the Upright (3) onto the welded bolts on the Frame (1). Be careful to avoid pinching the Resistance Cable (26) and the Sensor Wire (25). Tighten a 3/8O Nylon Locknut (29) onto each welded bolt. 2. Feed the console wire back down into the Upright (3). Attach the Console (6) to the Upright with four #8 x 3/4O Round Head Screws (16). Be careful to avoid pinching the console wire. Press the Resistance Knob (50) onto the Resistance Control (26). 2 1 Console Wire Console Wire Console Wire 3 1 25 26 29 3 50 26 6 16 26 Console Wire 25 1a 6 3. Attach a Pedal (31) to one of the Pedal Arms (12) with three #8 x 3/4O Round Head Screws (16) as shown. Repeat this step to attach a Pedal to the other Pedal Arm (not shown). 4. Make sure that there are Pedal Arm Bushings (42) in the ends of both Pedal Arms (12). Identify the Left Handlebar (8) (there is a decal on the Left Handlebar for identification). Slide a Handlebar Spacer (39) and one of the Pedal Arms (12) onto the Left Handlebar as shown (these parts fit tightly; it may be helpful t...

Herunterladen

Geben Sie zwei Ziffern: