Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Healthrider Dateigröße: 351.81 kb Dateiname: a05aa929-3ee8-485e-96ec-f4ba78b3e072.pdf Unterrichtssprache:

Tighten a 3/8O Nylon Locknut (29) onto each welded bolt. 2. Feed the console wire back down into the Upright (3). Attach the Console (6) to the Upright with four #8 x 3/4O Round Head Screws (16). Be careful to avoid pinching the console wire. Press the Resistance Knob (50) onto the Resistance Control (26). 2 1 Console Wire Console Wire Console Wire 3 1 25 26 29 3 50 26 6 16 26 Console Wire 25 1a 6 3. Attach a Pedal (31) to one of the Pedal Arms (12) with three #8 x 3/4O Round Head Screws (16) as shown. Repeat this step to attach a Pedal to the other Pedal Arm (not shown). 4. Make sure that there are Pedal Arm Bushings (42) in the ends of both Pedal Arms (12). Identify the Left Handlebar (8) (there is a decal on the Left Handlebar for identification). Slide a Handlebar Spacer (39) and one of the Pedal Arms (12) onto the Left Handlebar as shown (these parts fit tightly; it may be helpful to use the rubber mallet). Refer to the PART IDENTIFICATION CHART on page 5 and identify the 3/4O Axle Caps (43). Tap a 3/4O Axle Cap onto the Left Handlebar. Repeat this step to attach the other Pedal Arm (12) to the Right Handlebar (9). 5. Slide a Pedal Arm Spacer (41) and the left Pedal Arm (12) onto the axle on the left Pulley Arm (34) (these parts fit tightly; it may be helpful to use the rubber mallet). Be careful not to confuse the left Pedal Arm with the right Pedal Arm (not shown); look at the position of the Left Handlebar (8) to identify the left Pedal Arm. Tap a 3/4O Axle Cap (43) onto the axle on the left Pulley Arm (34). Repeat this step to attach the right Pedal Arm (not shown). 3 16 31 12 43 4 42 12 8 39 9 12 5 8 12 41 43 34 7 6. Refer to drawing 6a. Push the left Pedal Arm (12) until the axle on the left Pulley Arm (34) is at the back of the Side Shields (4, 5) as shown. Slide a Weld Spacer (49) and a Pivot Bushing (56) onto the left axle on the Upright (3). Make sure that the open side of the Weld Spacer is facing the Upright and that the Pivot Bushing is turned as shown. Slide the Left Handlebar (8) onto the left axle on the Upright (3). Make sure that the Left Handlebar slides onto the Pivot Bushing (56) on the axle. Slide another Pivot Bushing (56) onto the axle and start it into the Left Handlebar. Using a rubber mallet and the extra Pedal Arm Spacer (41, not shown), tap the Pivot Bushing into the Left Handlebar. Remove the Pedal Arm Spacer. Tap a 5/8O Axle Cap (57) onto the axle. Repeat this step to attach the Right Handlebar (not shown). 7. Attach the T-Handle (10) to the Upright (3) with two 1/4O x 3/4O Screws (54) and two 1/4O Black Nylon Locknuts (55). 8. The Console (6) requires two OAAO batteries (not included). Alkaline batteries are recommended. To install batteries, first locate the battery clip under the Console (6). Insert two batteries into the battery clip as shown. Make sure that the batteries are turned so the negative ends of the batteries (marked O.O) are touching the springs in the battery clip. 6 8 7 55 54 10 3 Batteries Ba...

Herunterladen

Geben Sie zwei Ziffern: