Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Step 2 Attach Middle Base (2) to Right Rear Upright (3) and Inner Base (1) using Bolts (42), Washers (53) and Nylon Lock Nuts (54). Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Step 3 NOTE: Before completing any other steps, you should position noth ends of the unit 12 ft apart from each other to accommodate the Cross Tube (11). This will keep you from having to move the unit once it is loaded with weights. Slide Weight Bumpers (38) and Guide Rods (9) onto holes of Middle Base (2). Slide quantity 9 of the 10 lb. plates (33) onto guide rods. Then slide quantity 10 of the 5 lb. plates (34) onto guide rods. Slide Top Plate (32) onto top of weight stack. Insert Weight Pin (35) Repeat STEP 3 on other side. Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Step 4 Insert Left Slide Frame (6) onto Slide Guide Tube (5) as shown and lock into one of the holes in tube. Attach Slide Guide Tube (5) to Inner Base (1) with Bolt (41), Washers (53) and Nylon Lock Nut (54). Slide Top Frame (8) onto Guide Rods (9) and Slide Guide Tube (5) and connect as shown, using Bolts (46), Washers (53), Nylon Locknut (54) and Bolt (44). Secure Top Frame (8) to Left Upright (4) using Bolts (40), Washers (53) and Nylon Lock Nuts (54). Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Step 5 Insert Right Slide Frame (7) onto Slide Guide Tube (5) as shown and lock into one of the holes in tube. Attach Slide Guide Tube (5) to Inner Base (1) with Bolt (41), Washers (53) and Nylon Lock Nut (54). Slide Top Frame (8) onto Guide Rods (9) and Slide Guide Tube (5) and connect as shown, using Bolts (46), Washers (53), Nylon Locknut (54), and Bolt (41). Secure Top Frame (8) to Right Upright (3) using Bolts (40), Washers (53) and Nylon Lock Nuts (54). Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Step 6 Slide Top Cross Tube (11) into both sides of the Top Frame (8) and secure as shown, using Bolts (41), Washers (53) and Nylon Lock Nuts (54). Note: two people will be needed to complete this step safely. Connect Chin-Up Handle (16) to Top Cross Tube (11) using Bolts (48), Washers (53) and Nylon Lock Nuts (54). 10 Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Step 7 Secure Big Pulleys (20) to Double Pulley Bracket (13) using Bolts (43), Washers (53), and Nylon Lock Nuts (54). Secure Double Pulley Bracket (13) to Left Slide Frame (6) using Bolt (47), Small Bushings (36) and Nylon Lock Nuts (54). Secure Big Pulleys (20) to unit using Bolts (40), Washers (53) and Nylon Lock Nuts (54). Attach Small Pulleys (21) to unit using Bolts (40), Washers (53), Pulley Spacers (37) used on the two pulleys on the Top Frame (8), and Nylon Lock Nuts (54). Insert Cable (15) through the pulleys in the Double Pulley Bracket (13) and install as shown. Secure cable end to Left Slide Frame (6) using Bolt (44), Washers (53) and Nylon Lock Nuts (54). Repeat for Right Side. 11 Assembly NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Step 8 Attach Handle (10) to each side of frame and secure with Bolts (39) and Washers (51). TIGHTEN ALL BOLTS AND NUTS before continuing! Once all bolts and nuts are tightened, then attach Weight Shrouds (12,62,63) with Allen Bolts (49) and Washers (52). 12 Parts List KF-CC Parts list Rev ARef #Part #descriptionQty1 3-010 BASE, INNER KF-CC 3-010 3BASE, MIDDLE KF-CC 3 3-010 4UPRIGHT, REAR RIGHT KF-CC14 3-010 5UPRIGHT, LEFT REAR KF-CC15 3-010 TUBE, SLIDE GUIDE KF-CC 19-000 LEFT SLIDE FRAME KPS-CC1 19-00059RIGHT SLIDE FRAME KPS-CC18 19-00 09FRAME, TOP KF-CC 9 3-00 85GUIDE ROD, KPS-CC410 19-00 08HANDLE, KF-CC 11 3-010 1TUBE, TOP CROSS KF-CC11 3-0095 WEIGHT SHROUD,TOP KF-18 0413 19-00054DOUBLE PULLEY BRACKET KPS-CC, KPS-SCC 14 19-0004 SWIVEL PULLEY BLOCK KPS-CC, KPS-SCC 15 9-0001 CABLE KPS-CC P15 1 19-00 0 HANDLE, CHIN UP KF-CC11 19-00 SELECTOR ROD INRAY-GYMS 18 0 -00048JAM NUT 1/ " 18 0 -00048JAM NUT 1/ " 19 10-00 5 POP PIN (LOCKING), KF-45/KF-AAB 0 3-00 8BIG PULLEY 4.5" 1 3-00 31SMALL PULLEY, KPS-CC/CG/LATA/SCC10 10-000 1HAND STRAP INRAY GYM 3 10-00059ANKLE STRAP INRAY GYM 4 0 -00391SQUARE PLUG, 50.8 KF SERIES8 5 0 -00035PLASTIC SLEEVE, 3.5X50.84 0 -0010 PLUG 3 - KPS4 0 -00004PLUG 54 8 0 -00459GRIP, KPS-CC 30X 4X 0 9 0 -00055GRIPS KPS-CC 30x 4x500 30 0 -00054LONG GRIPS 30X 4X59 31 10-00008GEAR HOOK, KPS, 10-00008 3 3-00031TOP PLATE KPS-GYM 35 10-00004WEIGHT PIN 3 0 -0003 SMALL BUSHING KPS-CG43 0 -0003 PULLEY SPACER838 0 -000 WEIGHT BUMPER KPS439 0 -00 1SCREW, BUTTON HD SOCKET CAP M1 X3 440 0 -00 4 BUTTON HEAD SOCKET CAP SCREW M10X 5841 0 -00 5SCREW, BUTTON HEAD SOCKET CAP M10X 584 0 -00 34SCREW, M10X80 BUTTON HEAD SOCKET CAP443 0 -00 4SCREW, BUTTON HEAD SOCKET CAP M10X501044 0 -00 3SCREW, BUTTON HEAD SOCKET CAP M10X35 45 0 -00 SCREW, BUTTON HD SOCKET CAP M10X55 4 0 -00 SCREW, BUTTON ...