Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: AEG Dateigröße: 499.86 kb Dateiname: 944983EN.pdf Unterrichtssprache:

Removing the shelf support 1. Pull the front of the shelf support away from the side wall. 1 2 2. Pull the shelf support from the back of the side wall to remove it. To install the shelf support follow the procedure in reverse. Valid with telescopic runners: The retaining pins on the telescopic shelf runners must point to the front! Oven lamp WARNING! There is a risk of electrical shock. Oven lamp and the lamp glass cover can be hot. 20 20 Care and cleaning Before you change the oven lamp: • Deactivate the appliance. • Remove the fuses from the fuse box or deactivate the circuit breaker. CAUTION! Put a cloth on the bottom of the interior of the appliance. It prevents damage to the lamp glass cover and the cavity. Replacing the oven lamp: 1. You can find the lamp glass cover at the back of the cavity. Turn the lamp glass cover counterclockwise to remove it. 2. Clean the glass cover. 3. If necessary, replace the oven lamp with applicable 300°C heat-resistant oven lamp. Use the same oven lamp type. 4. Install the glass cover. Oven Ceiling You can fold down the heating element on the oven ceiling to clean the oven ceiling easily. WARNING! Before you fold down the heating element deactivate the appliance. Make sure that the appliance is cold. There is a risk of burns! Folding down the heating element 1. Remove the shelf support. 2. Hold the heating element with the two hands at the front 3. Pull it forwards against the spring pressure and out along the support on both sides. 4. The heating element folds down. The oven ceiling is ready to clean. Installing the heating element 1. Install the heating element in opposite sequence. Install the heating element correctly on the two sides above the support on the inner wall of the appliance. 2. Install shelf support. Oven door and glass panels To clean the oven door remove it. CAUTION! Be careful when you remove the door from the appliance. The door is heavy! What to do if… 21 Removing the oven door 1. Open the oven door as far as it goes. 2. Lift up clamping levers (A) on the two door hinges fully. 3. Close the oven door until the first position (angle approximately 45°). 4. Hold of the oven door with one hand on each side and pull it away from the oven at an upwards angle. AA 5. Now you can remove the inner glass panels and clean them. To install the door follow the procedure in reverse. The number of glass panels depends on the model. CAUTION! Put the oven door with the outer side down on a soft and level surface to prevent scratches Removing and cleaning the door glass panels 1. Remove the oven door. 2. Hold the door t (B) on the top edge of the door at the two sides and push inwards to release the clip seal. 3. Pull the door t to the front to remove it. B 4. Hold the door glass panels on their top edge one by one and pull them up out of the guide 5. Clean the door glass panels. To install panels follow the procedure in reverse. Install the smaller panel first, then the larger. WHAT TO DO IF… WARNING! Refer to "Safety information" chapter. 22 22 Environment concerns Problem Possible cause Remedy The cooking zones do not operate The oven does not heat up The oven does not heat up The oven lamp does not operate Steam and condensation settle on the food and in the oven cavity face The oven is not switched on The fuse in the fuse box is released The oven lamp is defective You left the dish in the oven for too long Consult the operating instructions for the built-in cooking sur- Switch on the oven (refer to chapter "Daily use") Control the fuse. If the fuse is released more than one time, refer to a qualified electrician. Replace the oven lamp Do not leave the dishes in the oven for longer than 15-20 minutes after the cooking process ends If you cannot find a solution to the problem yourself, contact your dealer or the service centre. The necessary data for the service centre is on the rating plate. The rating plate is on the front frame of the oven cavity. We recommend that you write the data here: Model (MOD.) ......................................... Product number (PNC) ......................................... Serial number (S.N.) ......................................... ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. Packaging material The packaging material is environmentally-friendly and recyclable. Plastic parts are marked with internation...

Herunterladen

Geben Sie zwei Ziffern: