Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Remove the motor hood and vacuum the motor compartment. Check the motor belt for cracks and other wear. Check the motor for arcing; check for noises or odors. Lubricate the walking platform. Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week 10 Week 11 Week 12 Week 13 Week 14 Week 15 Week 16 Week 17 Week 18 Week 19 Week 20 Week 21 Week 22 Week 23 Week 24 Week 25 Week 26 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /Walking Platform Turned/Replaced Walking Belt Replaced/ / / / 32 TROUBLESHOOTING Most treadmill problems can be solved by following the steps outlined in this section. Find any symptoms that apply, and follow the steps listed. If further assistance is needed, please contact your distributor. 1. SYMPTOM: THE POWER DOES NOT TURN ON a. Make sure that the power cord is plugged into a properly grounded outlet. (Refer to page 10.) b. Make sure that the key is inserted into the console. c. Check the on/off circuit breaker located on the treadmill near the power cord. Make sure that the on/off circuit breaker is switched to the on position. “On” Position c 2. SYMPTOM: THE POWER TURNS OFF DURING USE a. Check the on/off circuit breaker located on the treadmill near the power cord. (See drawing 1. c. above.) Make sure that the on/off circuit breaker is switched to the on position. b. Make sure that the power cord is plugged in. c. Remove the key from the console. Reinsert the key into the console. d. If the power still turns off during use, please call Customer Care toll-free. 3. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON a. If the walking belt is overtightened, performance may a decrease and the walking belt may be damaged. If the walking belt is properly tightened, you should be able to lift each side of the walking belt 2.5 cm to 5 cm off the walking platform. If adjustments need to be made, first remove the key and unplug the power cord. Using the included allen wrench, turn both roller adjustment bolts counterclockwise 1/4 of a turn. Be careful to keep the walking belt centered. Plug in the power cord, insert the key, and use the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b. If the walking belt still slows when walked on, contact your distributor. Roller Adjustment Bolts 2.5–5 cm 33 a 4. SYMPTOM: THE WALKING BELT IS OFF-CENTER a. If the walking belt has shifted to the left: Remove the key and unplug the power cord. Using the included allen wrench, turn the roller adjustment bolts in the directions shown, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and use the treadmill for a few minutes. Repeat until the walking belt is centered. b. If the walking belt has shifted to the right: Remove the key and unplug the power cord. Using the included allen wrench, turn the roller adjustment bolts in the directions shown, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and use the treadmill for a few minutes. Repeat until the walking belt is centered. c. If the walking belt slips when walked on: Remove the key and unplug the power cord. Using the included allen c wrench, turn both roller adjustment bolts clockwise 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 1 to 2 inches off the walking platform. The center of the walking belt should just touch the walking platform. Make sure to keep the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. 5. SYMPTOM: THE WALKING BELT STOPS OR THE INCLINE CANNOT BE ADJUSTED EVEN THOUGH THE CONSOLE REMAINS LIT a. This indicates that a controller error may have occurred. To correct the problem, refer to step 8 on page 23. 6. SYMPTOM: THE TREADMILL DOES NOT APPEAR TO BE AT THE INCLINE LEVEL SHOWN IN THE MAIN DISPLAY a. The incline system may need to be calibrated. To initiate the calibration routine, hold down the SPEED + button and the SPEED – button simultaneously for two seconds. During the calibration routine, the treadmill will automatically rise to the highest incline level and then return to the lowest incline level. 7. SYMPTOM: THE WORDS LUBRICATE DECK APPEAR IN THE MAIN DISPLAY a. If the words LUBRICATE DECK appear in the main display, the walking platform should be lubricated. Follow the instructions in step 4 on page 29 to lubricate the walking platform. After you have lubricated the walking platform, hold down the STOP button and the RESET button simultaneously for...