Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Fotos und technische Daten Life Fitness S9i |
Anleitung Zusammenfassung
Conservez l'emballage au cas ou vous devriez renvoyer l'appareil. . LISEZ le manuel de l'utilisateur tout entier avant d'essayer de faire fonctionner cet appareil. Ceci est indispensable a son utilisation correcte. TOOLS REQUIRED FOR ASSEMBLY... Phillips Screwdriver, T27 Torx Wrench, Socket Set PARTS DESCRIPTION 1 Hex Head Bolt 3/8 – 16 x 3 0017-00101-1048 Qty: 2 3 Hex Head Bolt 5/16 – 18 x 1 0017-00101-0933 Qty: 2 5 Phillips Pan Head Screw #8 – 18 x .625 0017-00101-1243 Qty: 8 7 Phillips Pan Head Screw #8 – 18 x .75 0017-00101-1242 Qty: 4 9 Display Console Assembly Qty: 1 11 Accessory Tray Qty: 1 13 Handlebar Assembly Qty: 1 15 Telemetry Cable Qty: 1 17 Power Supply Qty: 1 2 Lock Nut Qty: 2 3/8 – 16 0017-00103-0025 4 Torx Cap Screw Qty: 10 1/4 – 20 x .625 0017-00101-1715 6 Polar Cover Qty: 1 8 Phillips Cap Screw Qty: 2 #6 – 32 x .375 0017-00101-1723 10 Monocolumn Qty: 1 12 Vertical Handrail Qty: 2 14 Polar® Receiver Qty: 1 16 Frame Cap Qty: 2 18 Monocolumn Shroud Qty: 1 1 2 543 7 8 10 18 C D B 2 18 10 1 E B 13 F 10 D H 1. Before proceeding, familiarize yourself with the parts of the Stairclimber and make sure that you have received all the items described in the Parts List. 2. Locate the MONOCOLUMN (#10). Position the MONOCOLUMN SHROUD (#18) onto the MONOCOLUMN as shown. Position the MONOCOLUMN near the MONOCOLUMN MOUNTING BRACKET (B) as shown. Detach and feed the CONSOLE WIRE HARNESS (C) through the MONOCOLUMN and out through the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE. Pivot the MONOCOLUMN upright and position the locating slot at the bottom of the MONOCOLUMN onto the pre-installed LOCATING BOLT (E) on the MONOCOLUMN MOUNTING BRACKET. Align the mounting holes of the MONOCOLUMN and MONOCOLUMN MOUNTING BRACKET and secure them together using two MOUNTING BOLTS (#1) and LOCKNUTS (#2). Leave the BOLTS and NUTS loose at this time. Lower the MONOCOLUMN SHROUD until it rests on the MAIN SHROUDS. CAUTION: BE CAREFUL NOT TO PINCH THE WIRE HARNESS WHEN ASSEMBLING THE MONOCOLUMN (#10) TO THE MONOCOLUMN MOUNTING BRACKET (B). 3. Align and insert the HANDLEBAR ASSEMBLY (#13) into THE HANDLEBAR BRACKET TUBE (F) as shown until the mounting holes in the HANDLEBAR ASSEMBLY align with those of the HANDLEBAR BRACKET TUBE. 13 F 10 4 4 J 6 8 13 F 8 14 4. Locate the TELEMETRY CABLE (#15). Feed the 3-PIN CONNECTOR (3P) end of the cable through the front of the HANDLEBAR ASSEMBLY (#13). The cable must be routed down the HANDLEBAR BRACKET TUBE (F) and back up the top of the MONOCOLUMN (#10). Feed the 3-PIN CONNECTOR through the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE. 5. Secure the HANDLEBAR ASSEMBLY (#13) to the HANDLEBAR BRACKET TUBE (F) using six MOUNTING SCREWS (#4). Tighten the SCREWS securely. 6. Locate the POLAR RECEIVER ASSEMBLY (#14). Plug the POLAR RECEIVER ASSEMBLY into the POLAR RECEIVER JACK (J). Place the POLAR RECEIVER in a vertical position, POLAR RECEIVER JACK facing downward, at the front of the HANDLEBAR BRACKET TUBE (F). Position the POLAR COVER (#6) over the center of the HANDLEBAR ASSEMBLY (#13) at the HANDLEBAR BRACKET TUBE. Making sure the POLAR COVER is oriented properly, slide the POLAR COVER over the HANDLEBAR ASSEMBLY covering the POLAR RECEIVER ASSEMBLY and the end of the HANDLEBAR BRACKET TUBE. The POLAR COVER should fully nest over the HANDLEBAR ASSEMBLY. Secure the POLAR COVER using two MOUNTING SCREWS (#8). CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS PAN HEAD SCREWS (#8). MISE EN GARDE : NE SERREZ PAS EXCESSIVEMENT LES VIS CRUCIFORMES A TETE CYLINDRIQUE (N. 8). 10 3P 13 F D 15 13 4 12 K 3 5 10 D 5 11 9 L 16 K 7. Locate one of the VERTICAL HANDRAILS (#12). Carefully insert the top of the VERTICAL HANDRAIL into the user right end of the HANDLEBAR ASSEMBLY (#13). Align the mounting holes. Secure the VERTICAL HANDRAIL to the HANDLEBAR ASSEMBLY using two MOUNTING SCREWS (#4). Position the bottom of the VERTICAL HANDRAIL over the mounting hole in the top of the right FRAME LEG (K). Using one HEX HEAD BOLT (#3), mount the VERTICAL HANDRAIL to the right FRAME LEG as shown. Tighten the BOLT securely. Repeat the procedure for the remaining VERTICAL HANDRAIL (#12) on the left side of the HANDLEBAR ASSEMBLY and FRAME. 8. Lift the MONOCOLUMN SHROUD (#18) and tighten the MONOCOLUMN BOLTS (#1) securely. CAUTION: DO NOT OVER-TIGHTEN THE BOLTS (#1). MISE EN GARDE : NE SERREZ PAS TROP LES BOULONS (N. 1) 9. Using four MOUNTING SCREWS (#5), attach the ACCESSORY TRAY (#11) to the DISPLAY CONSOLE (#9) as shown. CAUTION: DO NOT OVER-TIGHTEN THE SCREWS (#5). MISE EN GARDE : NE SERREZ PAS TROP LES VIS (N. 5) 10. Attach all CABLES (L) leading from the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE to the back of the DISPLAY CONSOLE (#9). 11. Feed any excess cable into the MONOCOLUMN (#10). Using four MOUNTING SCREWS (#5), secure the DISPLAY CONSOLE (#9) to the DISPLAY CONSOLE MOUNTING BRACKET (D). CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS HEAD PAN SCREWS (#5). CAUTION: BE CAREFUL NOT TO PINCH THE WIRE HARN...