Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
This product must be assembled on a flat, level strfface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To mirthnize risk, please follow these rules: 1.Inspect equipmentdaily. Tighten all loose connections and replace worn iparts immediately. Failure to do so may result in serious injury. 2.Donot allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. Tools Required for Assembly I * Rubber mallet or hammer * 3/4" wrench * 9/16" wrench * Ratchet with 3/4" and 9/16" sockets * 5/32" Allen wrench * Adjustable wrench * Tape measure Bolt Length Ruler ’] NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: ~KE. PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 6697803 TOWER 1 29 6140701 1 X 1 CrLIDE 2 6662303 LEG EXT HANDLE LEFT 1 30 3102407 3 X 2" END CAP 2 6662203 LEG EXT HANDLE RIGHT 1 31 6628302 1/8 X 2 X 8" PLATE 1 6705501 4 OD X 7" ROLLER PAD 6 32 3202114 1/2 X BOLT 1 6523401 3/4 OD X 72-.3/8" GUIDE ROD 2 33 3102917 1/2 X BOLT 6 6699302 PAD SLEEVE 2 34 3102910 1/2 X BOLT 4 6700303 B,ENCH FRAME 1 35 3102915 3/8 X ~-1/4," BOLT 2 6698003 LOWER CROSS SUPPORT 1 36 3102922 3/8 X 2-3/4," BOLT 4 6698903 LEG PEDESTAL 1 37 3102933 3/8 X BOLT 5 6698603 TOWER BRACE 1 38 3102909 3/8 X BOLT 7 6698303 UPPER CRDSS SUPPORT 1 39 3202401 3/8 X 1" BTN I-I CAP SCREW 5 6625502 PAD SUPPORT RIGHT 1 40 3102502 1/2" WASHER 10 6693502 PAD SUPPORT LEFT 1 41 3102501 3/8" V HER 15 66373XX BACK PAD 1 42 3114502 3/8" LOCKWASHER 3 66370XX SEAT PAD 1 43 3102801 1/2" LOCK NUT 11 6704101 FRONT SHROUD 1 44 3102802 3/8" LOCIK NUT 10 6704201 REAR SHROUD 1 45 6406401 HIN~ TAB 2 6695501 3/4 DIAX 18-1/4" SHAFT 1 46 6466901 1/2" St’RING PIN 1 6284501 6628401 20 HOLE WEIGHT STACK SHAF] IKEAD PLATE 1 1 47 48 6412001 6214401 3/8" SI,’RaqqG PIN 2 1 ’ "3116101 4.-1/2" PULLEY 3 49 3105401 STARLOI ’,K COLLAR 6 3116201 3,-1/2" PULLEY 2 50 6020601 1/2" FLAN’ )E BEARING 2 " " 6695401 175-1/2" CABLE 1 51 6695001 3/4" DIA Tt ’ED SHAFT 1 3108901 2" OD PLASTIC WASHER 8 52 6703801 WEIGHT STA ~2LABEL LBS. 1 6382301 WEIGHT PLATE BUSHING 10 CT 4 53 6703901 WEIGHT STA ’,K LABEL KGS. 1 3108002 WEIGHT STACK CUSHJON 2 54 6214501 WEIGH ’PLATES 20 6166701 2-7/8" L BRACKET 1 55 3104901 3/4" FLANk IBEARINGS 2 3116001 1-1/4. S ~ RUBBER BUM~ER 1 I LEG ]EXTENSION 1/2 X3" ~ FIGURE 1 STEP 1: . LOOSELYassemble LOWERCROSS SUPPORT (8) to the TOWER.(1) and BENCH FRAME(7) four 1/2" WASI-~RS(40) and four 1/2" LOCKNUTS (43). See FIGURE . LOOSELYassemble UPPI~ CROSS SUPPORT(11) to the TOWER(1) and BENCH FRAME(7) four 1/2" WASHERS(40) and four 1/2" LOCKNUTS (43). See FIGURE using using four four 4" BOLTS (33), 1/2 X 3" BOLTS . SECURELY TIGHTEN _ALL "][’HE CONNECTIONS MADE UP TO THIS POINT. I I 1/2 [" 1 1/2 [ I I 2 I I 1/2 [ I [ 3 I 4 I 1/2 [ I I I I 1/2 [ 1/2 ] 6 FIGURE 2 STEP 2: . SECURELY the LEFT (2) and RIGHT (3) to the BENCHFRA_ME(7’ using two 3/8 X 3-1/4" assemble LEG EXT. HANDLES BOLTS(35), four 3/8" W.~SHERS(41), and two 3/8" LOCKNUTS (44). See FIGURE . Slide two HINGE TABS (4.5) onto the BENCHFRAME(7) as shown in FIGURE STEP 3: SECURELYassemble one 1/8 X 2 X 8" PLATE (31) tothe SEAT PAD (15) using two 3/8X 1" BOLTS (38) and two 3/8" WASHERS See FIGURE (41). FIGURE 3 / / I / / 3/8 X 1"! FIGURE 4 STEP 4: . SECURELY SEAT PAD (15) to HINGE TABS (45) using two 3/8 X 1" BOLTS (38) and two 3/8" (41).assemble WASHERS FIGURE 4. . assemble BENCHSECURELY one. 1/2" SPRING PIN (46) to the FRAME(7) as shown in FIGURE FIGURE 5 STEP 5: Assemble RIGHT (12) & LEI~I " (13) PAD SUPPORTSto the BENCH FtLA~.~IE (7) using one 1/2 6" BOLT (32), two 1/2" lZL.~a’qGE BEARINGS (50), and one 1/2" LOCK NUT (43) as shown in FIGURE 5. (NOTE:Securely tightest, then back nut off 114 turn to allow the two parts to rotate freely.) 112 X 6" ~ 1/2 [ 1/2 I 6 3/8 X 2-3/’4" FIGURE 6 STEP 6: . SECURELY BAC~K to the RIGHT & LEFT PAD SUPPORTS (13) using four 3/8 X 2-3/4" assemble PAD (14) (12) BOLTS and -four 3/8" WASHERS as shown in (,11) FIGURE FIGURE 7~~ STEP 7: Aseemble two ROLLER PADS (4) to the BENCHFRAME(7) using one 18-1/4" SHAFT (18), four PLASTIC WASHERS and two STARLOCK COLLARS(49) as shown in FIGURE Assemble one 1-1/4" RUBBER (28) to the middle of the plate FRAME as BUMPER on the BENCH (7) shown on ]~IGUtLE E.EARZIqGS (9), Insert two 3/4" FLANGE (55) into the bushing of the LEG PEDESTAL then slide the 3/4" DIA TAPPED SHAFT (51) into the 3/4" BEARINGS as shownin FIGURE FLANGE! (55) 7 -STEP 8: AttachLEG PEDESTAL (9) to ~hc BENCH FRAME (7)usingtwo 3/8 X I" BuTroN HEAD CAP SCREWS (39) and m’o 318" LOCKWASHERS (42) as shown in FI...