Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Sears, modell PRO-FORM 500-CX PATL41106.0

Hersteller: Sears
Dateigröße: 3.62 mb
Dateiname: 61e4401a-7f62-4dcb-ad3b-cdd976bf17a5.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included hex key and your own phillips screwdriver .shaft at least 15 cm [6 in.] long) and wire cutters (with a For help identifying the assembly hardware, see the drawings below. The number in parentheses below each drawing is the key number of the part, from the PART LIST on page 31. The number following the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it has been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly. Wheel Nut (13)–211” Tek Screw (22)–4Handrail Bolt (64)–4Extension Leg Bolt (96)–43Star Washer(2Star Washer (8)–8Console Bolt (64)–4Extension Leg Nut (67)–4LExtension Leg Bolt (65)–4SScrew (3)–2Extension Leg Bolt (96)–4 1. Make sure that the power cord is unplugged. 1 With the help of a second person, carefully tip the treadmill onto its left side as shown. Partially fold the Frame (58) so the treadmill is more stable. Do not fully fold the frame until the treadmill is completely assembled. Attach four Base Pads (82) (only two are shown) to the base of the Uprights (84) with four 1” Tek Screws (22). Insert an Extension Leg (89) into the base of the Uprights (84) as shown. Hold two Extension Leg Nuts (67) in the bottom of the Extension Leg. Next, insert two Extension Leg Bolts (65) with Star Washers (8) into the top of the Extension Leg, and firmly tighten the Extension Leg Bolts into the Extension Leg Nuts. With the help of a second person, carefully tip the treadmill onto its other side. Attach the other Extension Leg (not shown) as described above. 89 58 8282 84 22 65 8 67 6 2. With the help of a second person, carefully raise the Uprights (84) to a vertical position. Have the second person hold the console assembly near the Uprights (84) as shown. Look under the console assembly and locate the Console Wire Harness (78). Remove the tie securing the Upright Wire Harness (77) to the right Upright (84). Next, connect the Upright Wire Harness to the Console Wire Harness (78). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and then try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 3. Insert the Wire Harnesses (77, 78) down into the right Upright (84). Set the console assembly on the Uprights (84). Be careful to avoid pinching the Wire Harnesses (77, 78). While a second person holds the console assembly, attach it with four Console Bolts (64) and four Star Washers (8) as shown; start all four Console Bolts and then firmly tighten them. 4. Orient the Latch Housing (73) so the large hole is on the indicated side. Attach the Latch Housing to the left Upright (84) with two Screws (3); start both Screws before tightening either of them. Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Next, insert the pin into the Latch Housing (73). Then, tighten the knob back onto the pin. Plug in the power cord as described on page 10, and turn on the power as described on page 12. Note: The treadmill may automatically rise to the maximum incline level and then return to the minimum level. Console Assembly 64 77, 78 64 8 8 84 84 3 84 77 78 2 Console Assembly 77 78 3 Pin Spring Collar Knob 73 4 84 Large Hole 7 5. Place the treadmill in the storage position (see HOW TO FOLD AND MOVE THE TREADMILL on page 24). Set the cylinder end of the Gas Spring (92) near the bracket on the base of the Uprights (84). See the two small inset drawings. Using your fingernail or the end of a screwdriver, press on the end of the Spring Pin (25), pivot it, and pull it out of the Gas Spring (92). Be careful to avoid losing the Spring Pin. Note: Extra Spring Pins are included. See drawing 5a. Press the cylinder end of the Gas Spring (92) onto the ball on the bracket. Next, insert the end of the Spring Pin (25) into two of the small holes in the end of the Gas Spring. Then, pivot the Spring Pin until it clips onto the Gas Spring. 5 92 84 25 Bracket Cylinder 25 25 92 5a 25 Bracket 6. Raise the free end of the Gas Spring (92) to a vertical position. Remove the Spring Pin (25) from the free end of the Gas Spring as described in step 5. If necessary, rotate the Gas Spring to align the end of the Gas Spring with the ball on the bracket on the Frame (58). Plug in the power cord as described on page 10. Turn on the power as described on page 12. Next, press the Incline increase an...