Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
PART CHART Use the part drawings below to identify the small parts used in assembly. The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on page 14. The second number refers to the quantity used in assembly. Note: Some small parts may have been pre-attached for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled. M8 x 70mm Carriage Bolt (72).2 Console Screw (20).8 M8 Nylon Locknut (56).8 M8 Curved Washer (28).7 M8 x 85mm Carriage Bolt (63).2 M8 Black Flat Washer (57).16 M8 x 40mm Carriage Bolt (7).4 M6 x 38mm Hex Screw (73).4 M6 x 15mm Hex Screw (29).4 M8 x 15mm Button Screw (74).4 M8 x 45mm Button Screw (17).3 4 1. Attach the Front Stabilizer (2) to the front of the Frame (1) with two M8 x 70mm Carriage Bolts (72), two M8 Curved Washers (28), and two M8 Nylon Locknuts (56). Make sure that the Front Stabilizer is turned so the Roller (75) is not touching the floor. 2. Attach the Rear Stabilizer (3) to the rear of the Frame (1) with two M8 x 85mm Carriage Bolts (63), two M8 Curved Washers (28), and two M8 Nylon Locknuts (56). 3. While a second person holds the Upright (6) near the Frame (1), connect the Extension Wire Harness (18) to the Lower Wire Harness (44). Carefully slide the Upright (6) onto the Frame (1). Be careful to avoid pinching the wires. Attach the Upright with four M8 x 15mm Button Screws (74) and four M8 Black Flat Washers (57). Important: Make sure that the Upright is turned exactly as shown at the right. 1 7572 2 1 28 56 2 28 56 1 3 63 28 56 3 6 74 57 44 1 18 57 57 74 57 Upright must be turned as shown 5 6 5. While another person holds the Handlebar (16) near the Upright (6), connect the two Pulse Wires (22) to the corresponding wires on the Console (9) (refer to the inset drawing). Next, attach the Handlebar (16) to the Upright (6) with three M8 x 45mm Button Screws (17) and three M8 Curved Washers (28). Make sure that the Pulse Wires (22) are not caught between the Handlebar and the Upright. 6. Attach the Cup Holders (14) by firmly pushing them down into the indicated holes in the Upright (6) until they are seated fully. If there is a vinyl film covering the pulse grips, peel it off. 14 14 6 6 4. The Console (9) requires two OAAO batteries (not included); alkaline batteries are recommended. Refer to drawing A. Remove the four indicated screws and lift off the front of the Console. Press two batteries into the battery holder as shown in drawing B. Make sure that the negative (.) ends of the batteries are touching the springs. Re-attach the front of the Console. Make sure that the three wires are extending from the back of the Console. While another person holds the Console (9) near the Upright (6), connect the Extension Wire Harness (18) to the console wire harness. Set the Console (9) on the Upright (6). Tighten four Console Screws (20) into the Upright and the Console. 4 Batteries Screws Battery Holder B A 9 Console Wire Harness 6 20 20 18 17 22 28 16 6 5 Console Wires Pulse Grips 9 A 7. Attach the Seat Carriage (11) to the Seat Frame (27) using four M8 x 40mm Carriage Bolts (7), four M8 Black Flat Washers (57), and four M8 Nylon Locknuts (56). 8. Attach the Seat (12) to the Seat Frame (27) with four M6 x 15mm Hex Screws (29) and four M8 Black Flat Washers (57). 9. Attach the Backrest (13) to the Seat Frame (27) with four M6 x 38mm Hex Screws (73) and four M8 Black Flat Washers (57). 7 57 7 11 56 27 57 56 8 57 12 29 57 27 9 13 27 73 73 57 57 7 10. Turn the Seat Knob (8) counterclockwise two or three turns to loosen it (if the Seat Knob is not loosened enough, the Seat Knob may scratch the Frame [1]). Next, pull the Seat Knob and slide the Seat Carriage (11) onto the Frame (1). Move the Seat (12) to the desired position and release the Seat Knob. Make sure to move the Seat Carriage back and forth slightly until it locks in position. Then, turn the Seat Knob clockwise to tighten it. Attach the Nut (54) to the Frame (1) with the #10 x 5/8O Screw (30). 11. Identify the Left Pedal (40) (there is an OLO on the Left Pedal for identification). Using an adjustable wrench, tighten the Left Pedal counterclockwise into the Left Crank Arm (55). Tighten the Right Pedal clockwise into the Right Crank Arm in the same way (not shown). Tighten both Pedals as fully as possible. Important: After using the exercise cycle for one week, retighten the pedals. For best performance, the pedals must be kept properly tightened. Adjust the Pedal Strap (41) on the Left Pedal (40) to the desired position. Press the Pedal Strap onto the tab on the Left Pedal. Adjust the Pedal Strap on the Right Pedal in the same manner (not shown). 54 30 1 10 12 11 8 11 55 41 40 Tab 12. Make sure that all parts are tightened before you use the exercise cycle. Place a mat beneath the exercise cycle to protect the floor. HOW TO OPERATE THE RECUMBENT CYCLE HOW TO ADJUST THE POSITION OF THE SEAT For effective exercise, the seat should be in the proper pos...