Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Place (2) 3/8" Washers (Item #N) over the end of (2) 3/8” X 5" Button Head Screws (Item #K) -one washer per screw. Insert the screws through the lined up holes in the Chest Bar with Pulleys and the Lower Lat Tower, and secure each screw by placing (1) 3/8" Washers and (1) 3/8" Nylock Nuts (Item #O) over the end of each screw. Completely tighten hardware installed during Step 4. Base Platform/ Lower Lat Tower Assembly Figure 4 6 O K N Chest Bar Brackets Step 5 - Attach the Seat Bracket to the Seat Pad Locate the following items: • Item #7 - Seat Pad • Item #8 - Seat Bracket • Item #C - (4) 5/16" X 3/4" Button Head Screws • Item #M - (4) 5/16" Washers Place the Seat Pad (Item #7) on the floor, cushion-side down. Position the Seat Bracket (Item #8) so the cut-out is toward the angled edge of the Seat Pad. Align the four holes in the Seat Bracket with the four holes in the Seat Pad. Place(4)5/16"Washers (Item#M)over(4)5/16"X3/4"Button Head Screws (Item #C) -one over each screw, and use those screws to secure the Seat Bracket to the Seat Pad. Completely tighten hardware installed during Step 5. Figure 5 M C 8 7 Cut-out Angled Edge Assembly Guide Step 6 - Attach the Seat Rail to the Seat Assembly Locate the following items: • From Step 5 - Seat Pad/Seat Bracket Assembly • Item #9 - Seat Rail Undo the twist ties from the Rail Pivot Bushings and remove the Bushings. Set aside until the end of this step. Line up the Seat Rail (Item #9) with the Seat Assembly (from Step 5). Orient the Seat Rail so that the Pull Pin on the Seat Bracket is on the same side as the holes in the Seat Rail. Pull out the Pull Pin on the Seat Bracket, and then insert the Seat Rail through the Seat Bracket, (see Figure 6). To adjust the Seat, slide the Seat until the Pull Pin is aligned with one hole, then release the Pull Pin into the hole. Once you have attached the Seat Assembly to the Seat Rail, reinstall the Rail Pivot Bushings that you removed at the beginning of this step. Note: See Step 22 to adjust the Seat Bracket. Figure 6 9 Seat Pad/Seat Bracket Assembly Holes in the Seat Rail Pull Pin Rail Pivot Bushings Step 7 - Attach the Rear Leg to the Rear Leg Cross Tube Locate the following items: • Item #10 - Rear Leg -Do not unwrap cables! • Item #11 - Rear Leg Cross Tube • Item #H - (2) 3/8" X 3" Button Head Screws • Item #N - (4) 3/8" Washers • Item #O - (2) 3/8" Nylock Nuts Line up the holes in the bracket on the Rear Leg (Item #10) with the holes in the Rear Leg Cross Tube (Item #11) as shown in Figure 7. Place (2) 3/8" Washers (Item #N) over the end of (2) 3/8" X 3" Button Head Screws (Item #H) -one per each screw. Insert the screws through the lined up holes, and secure by placing (1) 3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the end of each screw, as shown in Figure 7. Completely tighten hardware installed during Step 7. Figure 7 H N O 10 11 Rear Leg Bracket Assembly Guide Step 8 - Attach the Rear Leg to the Seat Rail Locate the following items: • From Step 6 - Seat Rail Assembly • From Step 7 - Rear Leg Assembly • Item #J - (1) 3/8" X 4 1/4" Button Head Screw • Item #N - (2) 3/8" Washers • Item #O - (1) 3/8" Nylock Nut • Item #Q - (2) Bolt Covers Undo the twist ties from the Pivot Bushings on the end of the Rear Leg Assembly (from Step 6), but do not remove the Bushings. Note: When attaching the Rear Leg Assembly (from Step 7) to the Seat Rail Assembly, rotate the Rear Leg forward (as shown in Figure 8b), to allow the Leg Latch to engage with the Seat Rail Pull Pin. Align the holes on the End Bracket of the Seat Rail Assembly with the middle holes on the Rear Leg Assembly, (see Figure 8). Place (1) 3/8" Washer (Item #N) over the end of (1) 3/8" X 4 1/4" Button Head Screw (Item #J). Insert the screw through the lined up holes and then loosely secure on the opposite side by placing (1) 3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the end. Do not over-tighten hardware from Step 8. Note: Tighten the nylock nut enough that the threads of the screw extend through the nylock nut, but loosely enough that the Leg Assembly can move freely. At this time, place (1) Bolt Cover (Item #Q) over the Nylock Nut installed during Step 8, place 1 bolt cover over the Nylock Nut going through the rear leg pulley. Once you have completed Step 8, rotate the Rear Leg back until it engages the Seat Rail Pull Pin. Figure 8 J O Rear Leg Assembly Rail Assembly End Bracket Middle Hole N Figure 8b Rail Assembly Rear Leg Seat Rail Pull Pin Leg Latch Assembly Guide Step 9 - Attach the Seat Rail to the Main Assembly Locate the following items: • From Step 4 - Main Assembly • From Step 8 - Seat Rail Assembly • Item #12 - Seat Rail Knob • Item #J - (1) 3/8" X 4 1/4" Button Head Screw • Item #N - (2) 3/8" Washers • Item #O - (1) 3/8" Nylock Nut • Item #Q - (1) Bolt Cover Align the holes on the Seat Rail Assembly (from Step 8) with the holes in the Rail Bracket on the Main Assembly (from Step 4), as shown in Figure 9. Insert the Seat Rail Assembly into t...