Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Aiming Trigger Mode RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3 -9 - Data Capture for Workforce in Motion In Autoscan mode, the scan beam is continuously on. This mode enables to scan continuously. Autoscan In Smart Autoscan mode, for a battery power consumption optimisation issue, the scanner will be continuously flashing. Smart Autoscan The “No duplicate scan” option has been developed for users who do not want to scan the same barcode twice. « no duplicate scans » disabled (*) « no duplicate scans » enabled + error signal If the same barcode is scanned, an error signal is played (two beeps (lower tone) and a red enlightening of the led) « no duplicate scans » enabled + no decoding If the same barcode is trying to be scanned, it won’t be. The laser beam will still be enlightening. Data Capture for Workforce in Motion In Autoscan mode, the scan beam is continuously on. This mode enables to scan continuously. Autoscan In Smart Autoscan mode, for a battery power consumption optimisation issue, the scanner will be continuously flashing. Smart Autoscan The “No duplicate scan” option has been developed for users who do not want to scan the same barcode twice. « no duplicate scans » disabled (*) « no duplicate scans » enabled + error signal If the same barcode is scanned, an error signal is played (two beeps (lower tone) and a red enlightening of the led) « no duplicate scans » enabled + no decoding If the same barcode is trying to be scanned, it won’t be. The laser beam will still be enlightening. RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3 -10 - Data Capture for Workforce in Motion 1.4. Operating Mode Real Time mode In real time mode, the barcode is decoded and transmitted to the remote host without any delay. If the scanner is not connected, the data is lost. Real Time mode with No Data Loss option If the No Data Loss option is activated and if the scanner is not connected or out of Bluetooth range, the scanner will store the data. It can memorise up to 10 000 barcodes (UPC format) and later automatically upload them to the remote host when a Bluetooth connection is established to the host. Every barcode sent to the host must be acknowledged by the host. If the host fails to send an acknowledgement, the scanner will continue to transmit the barcode until the host does send an acknowledgement. This acknowledgment is disabled in the default settings. It is strongly recommended to set the No Data Loss mode to ON. This configuration can be set with the BaracodaManager software or with the Programming Guide. Additionally, this protocol acknowledgment allows an end user to set an audio acknowledgment indicating that the barcode has been successfully transmitted to the host. Batch mode Barcodes are always stored in the scanner. Once the batch mode is selected, the BCL led (right) emits an orange flash. In batch mode, the barcode can read up to 10 000 barcodes (UPC format) and store them into its non-volatile memory for later transmission to the host. When the internal memory is full, both Leds will be full orange (no blinking). To upload barcodes from the scanner, connect it to the host computer via Bluetooth. The BaracodaManager software is used to configure the location where the barcodes are sent once the barcodes are extracted from the scanner. Once connected, the scanner will wait for the appropriate command in order to start uploading the barcodes: this command can come from: · The BaracodaManager: The user has to click on the button “Upload”. · A configuration scan barcode: the user has to read the appropriate configuration barcode. Be aware that with BaracodaManager, two (2) different ways to upload barcodes are possible: · To an application window: In this case always double check before starting the upload procedure that the cursor in your text window is active. Otherwise you will loose all the data saved into your scanner. · To a .txt file (default option). The BaracodaManager gives you the possibility to modify the name of the file in which you may want to save the data. Data Capture for Workforce in Motion 1.4. Operating Mode Real Time mode In real time mode, the barcode is decoded and transmitted to the remote host without any delay. If the scanner is not connected, the data is lost. Real Time mode with No Data Loss option If the No Data Loss option is activated and if the scanner is not connected or out of Bluetooth range, the scanner will store the data. It can memorise up to 10 000 barcodes (UPC format) and later automatically upload them to the remote host when a Bluetooth connection is established to the host. Every barcode sent to the host must be acknowledged by the host. If the host fails to send an acknowledgement, the scanner will continue to transmit the barcode until the host does send an acknowledgement. This acknowledgment is disabled in the default settings. It is strongly recommended to set the No Data Loss mode to ON. This configuration...
Dieses Handbuch ist für folgende Modelle:Ladenausstattung & -werbung - LA (512.82 kb)