Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Honeywell Dateigröße: 295.57 kb Dateiname: 47110.pdf Unterrichtssprache:

CAUTION: When only the battery icon flashes on the display, the thermo- stat is shut down, and your system will no longer operate. In this condi- tion, there is no temperature control of your dwelling. NOTE: If you plan to be away from the premises over 30 days, we recommend that you replace the old batteries with new alkaline batteries prior to leaving. FEATURES day/time reset system heat cooloff program filter hold /return fan auto on Hold / Return Key: Used for setting a permanent (vacation) hold, and for returning to the normal display from Day & Time setting, Programming, or Span setting modes. LCD Display: Shows Time, Day, Temperature, Program Number, and other feature information as required. Low Battery Indicator: Flashes when batteries need to be replaced. System Switch: Selector switch for Heat, Cool, and Off Fan Switch: Fan switch for Automatic or Continuous fan operation. Battery Compartment: Front access allows easy insertion of two AA 1.5V batteries. Reset: Press with a paper clip to reset the thermostat and return to power-up settings. Front Door: Covers keys when not used for neat appearance. Open by lifting from the bottom Up and Down Keys: Keys for changing the Temperature setting. Also used for increasing and decreasing selections in the Time, Program, and Span functions. Day / Time Key: Used for entering the Clock setting mode. Use with the Up and Down keys to set the time and day. Program Key: Used for entering and modifying Programs. Use with the Up and Down keys to set times and temperatures. Press when in Clock setting mode to select between 12 and 24 hour clock modes. Filter Key: Resets filter change counter to zero. Battery Release Lever: Push to pop batteries loose. M AM 4 TEMP ENERGY STAR® PARTNER As an ENERGY STAR® Partner, Hunter Fan Co. has determined that this programmable thermostat meets the ENERGY STAR® guidelines for energy efficiency. INSTALLATION What You Need This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your thermostat, you should have the following tools and materials. ¦ Slotted Screwdriver(s) ¦ Small Philips screwdriver ¦ Hammer ¦ Electric drill and 3/16” bit ¦ Two 1.5 V (AA) size alkaline batteries Remove Old Thermostat CAUTION: Do not remove any wiring from existing thermostat before reading the in- structions carefully. Wires must be labeled prior to removal. ¦ IMPORTANT! Turn off the power to the furnace at the main power panel or at the furnace. ¦ Remove existing thermostat cover and thermostat. See Figure 1. Some thermostats will have screws or other locking devices that must first be removed. Once the wall mounting plate is exposed, look for wires. If wires are not visible, they may be connected to the back of the wallplate. Again, look for screws, tabs, etc. Some models have doors that open to expose wires and mounting screws. See Figure 1. Typical Home Thermostats Wall Mounting Plate Thermostat Cover Wall Mounting Plate Thermostat Cover Figure 1 Wire Labeling ¦ Each wire coming from the wall to the existing thermostat is connected to a terminal point on that thermostat. Each of these terminal points is usually marked with a code letter as shown in Table A below. ¦ The number of wires in your system can be as few as two (for heat only systems), as many as eight, or any number in between. If you follow the labeling procedures correctly, you do not have to be concerned about how many wires there are. ¦ There is often no terminal marking on the existing thermostat of two wire, heat only systems. Just connect either of the wires to the RH terminal, then connect the other wire to the W terminal to complete the circuit. ¦ IMPORTANT! BEFORE DISCONNECTING ANY WIRES, APPLY THE SELF-ADHESIVE LABELS PROVIDED TO THE WIRE AS SHOWN IN TABLE A BELOW. (For example, attach the label marked W to the wire that goes to the W or H terminal on your existing thermo- stat.) IGNORE THE COLOR OF THE WIRES since these do not al- ways comply with the standard. WGYRHRC(Continued) 3 ® W RH G RC x RH x RC x G Y x x RH, R, VR or4 24 Volt RC, VC 24 Volt Cool G or F Fan Y, C or M Air Conditioning Compressor W or H Heating If the code letter on your existing thermostat is then mark the wire with label shown and connect to thermostat terminal shown Y W W Y Rh Rc G ¦ Position wallplate on wall and pull existing wires through large opening. Then level for appearance. Mark holes for plastic anchors provided, if your existing holes do not line up with those on the Hunter wallplate. ¦ Drill holes with 3/16” bit and gently tap anchors into the holes until flush with wall. ¦ Reposition wallplate to wall, pulling wires through large opening. Insert mounting screws provided into wall anchor and tighten. See Figure 3. NOTE: 5-wire Systems If your thermostat has one wire marked R or RH (2, 3, or 4-wire system), then leave the jumper wire between the RH and RC terminals on the wallplate. Otherwise, if you have separate RH and RC wires (5-wire system), then re...

Herunterladen

Geben Sie zwei Ziffern: