Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: JVC Dateigröße: 778.97 kb Dateiname: 7fb4cf16-e2af-4a6b-a471-9cf8fcd2832a.pdf Unterrichtssprache:

1.TV is in antenna mode. 2.Current channel has no signal. 3.No key is pressed within 15 minutes. Connecting the Antennae Notes : 1. It is recommended that a 75 ohm coaxial cable be used in order to eliminate interference and noise which may occur due to nearby radio transmissions. 2. The antenna cable should not be tied together with other wiring. 3. Set up a lightning rod and check it regularly when an outdoor antenna is used. Installing the Remote Control Batteries 1. Remove the battery compartment lid. 2. Insert two AAA batteries (included). Make sure the positive (+) and negative (-) polarities are correctly aligned. 3. Reattach the battery lid. Notes: 1. Alkaline batteries are recommended for longer life. 2. Always replace both batteries at the same time. 3. Do not expose batteries to fire or break them open. 4. To avoid battery leakage, remove batteries from the remote control when it is not being used for a long period of time. VHF UHF or Cable VHF UHF 75-ohm coaxial cable (not supplied) 300-ohm twin-lead cable (not supplied) Antenna adapter (not supplied) U/V mixer (not supplied) RF Input (back of TV unit) Instruction Manual 7 Output from TV to Device DO NOT connect both composite (yellow video terminal) and S-Video terminal. Use only one of the two. Also, remember to connect the audio cables when using S-Video. Camcorder VCR AUDIO/VIDEO OUT AUDIO VIDEO VIDEO AUDIO NSTALLATION (continued) Connecting A/V Equipment The following are diagrams showing basic instructions for attaching external equipment, like a VCR or DVD player, to your TV set. Please refer to operation manuals of external audio/video equipment that will be connected to your set for additional instructions. PLEASE TURN OFF ALL POWER BEFORE CONNECTING DEVICES TOGETHER. Input from Device to TV The side terminals may be easier to use with a camcorder. The connections are identical. Coaxial Cable RF IN VCR DVD Player VCR AUDIO/VIDEO IN With S - VIDEO Terminal Connect VCR's RF OUT terminal to the RF IN jack located on the rear panel of the TV. Instruction Manual 8 Picture Tint . . . . . ! . . . . . 00 Brightness . . . . . ! . . . . . 32 Contrast . . . . . ! . . . . . 32 Color . . . . . ! . . . . . 32 Sharpness . . . . . ! . . . . . 32 FUNCTIONS & FEATURES Turn On/Off 1. Turn On Plug in the power cord, and the TV should enter into Standby mode. Pressing STANDBY key will turn on the TV and its power indicator light. 2. Standby While the TV is on, press the STANDBY key will put the TV in Standby or off mode. The power indicator light on the TV set will turn off. Basic Functions Changing the Channel While in Tuner mode, press the CH +/ - keys to change the channel, or use the numeric keypad to enter a new channel. Adjusting the Volume To adjust the volume, press the VOL +/ - keys. Also, you may press the FUNCTION (F) key along with the VOL +/ - keys to adjust the volume in increments or decrements of 4. Muting the Volume To mute the volume, press the MUTE key. To restore the volume, press MUTE again or press the VOL + key. Function Selection Menus To change the setting of any function, press the MENU key to bring up the main menu. Press the up or down arrow key to highlight the desire sub-menu and press the left or right arrow key (or ENTER key) to access. While in the sub-menu, use the up or down arrow key to select the item and the left or right arrow to adjust the setting. Press the MENU key to return to the main menu and exit. While in the setup menu, CH-/+ and VOL-/+ key on the front panel will function as the down/up/left/right arrow keys on the remote control. Picture Menu Features This menu allows you to adjust the various picture settings. Use the up or down arrow key to move between the various settings, and the left or right arrow key to adjust them. Tint: -31 (more purplish to +31 (more greenish) Brightness: 0 (dimmest) to 63 (brightest) Contrast: 0 (minimum contrast) to 63 (maximum contrast) Color: 0 (minimum color) to 63 (maximum color) Sharpness: 0 (minimum sharpness) to 63 (maximum sharpness) Instruction Manual 9 Tuner Channel 2 Add/Erase Add Antenna Air Auto Program < Stop Start > System Language Eng. Fra. Esp. Blue Back On CCD/Text Off Parental Guide On MPAA-X TV-MA FUNCTIONS & FEATURES (continued) Tuner Menu Note: This menu is only accessible while the TV is in Tuner mode. Channel: This feature allows you to change the channel displaying on screen. Use the left or right arrow key or the numeric keypad to change the channel. Add/Erase: This feature allows you to add or remove the channel currently display on screen to the "active channel list" . Active channel list is the list of channel that is available by pressing the CH+/- keys. Use the left or right arrow key to add or erase. Antenna: This feature sets the TV tuner to an Air antenna or a Cable antenna. Please use Air mode when using an over-the-air antenna; use Cable mode for a cable hookup. Use the left or right arrow key to select between the two options. Auto Program: T...

Herunterladen

Geben Sie zwei Ziffern: