Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
VCR Back Note: If you do not have a VCR connect signal directly to TV 75 ohm jack. S-Video Input Terminal on your external equipment. Audio Output Jacks L L L L (See page 6.) R R R R 480i Component Video In Jacks (Component 3, Y, Pb, Pr) Audio/Video Input Jacks (AV1 / AV2) Connect video equipment here. Connect video equipment here (see pages 5 ~ 6). (See page 6.) Note: S-Video connections override the AV1 and AV2 video connections. Operational Tip for No Signal Connection: If the TV is used as a monitor only, with a DVD player or some other type of external equipment, and no cable or antenna signal is available, the following setup is necessary: Your TV is designed to automatically search for available channels. Therefore, the initial start up requires that you press the MENU key, enabling the TV to automatically go through the channel search process before you can operate the TV. After the initial channel search is completed, you must press the MENU key again to complete the channel search process (may take several minutes). After the channel search process is complete (2 searches), you can press the INPUT key on the remote control to use the TV as a monitor. 4 Basic Set-up & Connections Using the Audio/Video Input Jacks Connecting a VCR or DVD PLAYER Switch off TV and external equipment before connecting cables. (Cables are not supplied.) . Connect VCR, DVD Player, or other equipment’s Audio Video Output to the TV Audio Video Input. For Mono VCR (Single Audio Jack) connect VCR Audio Output to TV Audio (L) Input. . Optional Connect DVD Player or other equipment’s S-Video Output to the TV S-Video Input Jack. Using the S-Video jack overrides the Video jack. . Press POWER to turn on the TV. Turn on external equipment also. . Press the INPUT key to select VIDEO1 or VIDEO2. IN OUT A/V JACKS L- RAUDIOVIDEO L- RAUDIOVIDEO S-VIDEO OUT RL S-VIDEO VIDEO AUDIO INPUT Y Pb Pr AV2 AV1COMPONENT R R R R L L L L(MONO) AUDIO OUTPUT VIDEO AUDIOAUDIO UHF/VHF/CATV 75.Back View of VCR Remote Control TV AV Input Jacks DVD Player What you will need for connections: . AV Cable – 1 OPTIONAL CONNECTION . S-Video Cable – 1 . Audio Cable – 1 . Press INPUT key after connecting cables to access the A/V inputs. There is NO need to tune to a blank channel. . . . . . . . INPUT POWER RESET DVD SAT AUX VCR TV CABLE QuickTips ¦ Make sure all cable connectors are fully seated on jacks. ¦ Always match A/V cables according to the colors; RED for right audio, WHITE for left audio and YELLOW for video. ¦ A solid Blue screen with VIDEO1 or VIDEO2, displayed means that a Video mode is selected, but no signal is being detected at the Video jacks. Check connections, and turn on external equipment. Need help? Visit our Web site at or Call 1-800-877-5032 Audio & Video Input Jacks 5 Connecting a DVD Player or other equipment Switch off TV and external equipment before connecting cables. (Cables are not supplied.) .Connect a DVD Player or other equipment’s interlaced Component Video Output to the TV Component Video Input (Y-Pb-Pr) Jacks. .Connect the DVD Player’s Audio Output to the TV Component L/R Jacks. .Press POWER to turn on the TV. Turn on external equipment also. .Press the INPUT key to select COMPONENT3. Note: DVD Player component output must be set to Interlaced (480i). Y PB PR VIDEO L AUDIO R COMPONENT VIDEO OUT A/V OUT S-VIDEO OUT S-VIDEO VIDEO AUDIO INPUT Y Pb Pr COMPONENT AV2 AV1 R R R R L L L L (MONO) (MONO) UHF/VHF/CATV 75. AUDIO OUTPUT VIDEO AUDIO AUDIO DVD Player . TV Back INPUT POWER RESET DVD SAT AUX VCR TV CABLE . Remote Control What you will need for connections: . Component video cable – 1 . Audio Cable – 1 What you will need for connections: . Audio Cable – 1 Using the Component Audio/Video Input Jacks QuickTips ¦ You may be able to use the TV remote control to operate your DVD Player. (See pages 9 ~11). ¦ A solid Blue screen with COMPONENT3 displayed means that the Component Video mode is selected, but no signal is being detected at the Component jacks. Check connection, and turn on external equipment. ¦ Position your TV at least 2 feet from stereo speakers. The magnets in the speakers may affect the picture quality. Need help? Visit our Web site at or Call 1-800-877-5032 . . Press INPUT key after connecting cables to access the A/V inputs. There is NO need to tune to a blank channel. . . S-VIDEO VIDEO AUDIO INPUT Y Pb Pr COMPONENT AV2 AV1 R R R R L L L L (MONO) (MONO) AUDIO OUTPUT VIDEO AUDIO AUDIO Back of TV Stereo Amplifier Using the Audio Output Jacks Connecting Audio Output Jacks to a Stereo Amplifier Switch off TV and external equipment before connecting cables. (Cables are not supplied.) . Connect the TV Audio Output (R/L) to the Stereo Amplifier In (R/L). . Press POWER to turn on the TV. Turn on external equipment also. .Use the AUDIO OUTPUT on-screen menu options to select Fixed or Variable output signal. Notes: DO NOT connect external speakers directly to the TV. When TV Speakers is in th...