Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
To ensure the safe operation of the unit, please read these instructions before installing. TABLE OF CONTENTS 1. Check for enclosed parts .............................. 2 2. Important Safety Instructions ........................ 3 3. Assembly Instructions ................................... 6 4. Adjusting angles after installation ................12 *To install the wall hanger unit, Please consult an Authorized service center first. 1 PLASMA DISPLAY HANGER UNIT 2 H W A A N L G L E R UNI T 1. PLEASE CHECK THE ITEMS SHOWN BELOW (2) FRAME SET A FRAME SET B CONNECTING FRAME CONCRETE WALL ANCHOR M5 SCREWS (20 MM) WALL SCREWS PAPER PATTERN PLAN M5 SCREWS (30MM) (2) (1) (8) (12) (8) (1) (2) Paper pattern plan 2. IMPORTANT SAFETY INSTRUCTIONS WARNING : Disregarding these instructions can result in serious injury. CAUTION : Disregarding these instructions will result in the mistreatment of the unit and can result in injury or damage to the unit. PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT. PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to vibrate and to fall) (Failing to do so may cause the unit to fall and break) (Failing to do so may cause the unit to fall and break) To install the wall hanger unit, please consult an Authorized service center first. The wall hanger unit needs to be installed securely enough to handle earthquakes or lengthy periods of vibration. When assembling, do not use any parts other than those enclosed and secure all parts tightly. Do not leave out any part when assembling. Please install all parts to where indicated. Do not alter or modify any parts Do not use the wall hanger unit with other products. This wall hanger unit is specifically designed to fit the Daewoo Plasma Display. *PLEASE CONSULT AN AUTHORIZED SERVICE CENTER TO INSTALL THE WALL HANGER UNIT WARNING CAUTION 3 PLASMA DISPLAY HANGER UNIT 4 H W A A N L G L E R UNI T Special care is needed when installing onto the wall due to its weight (35Kg) When installing on a concrete wall Please be sure to use the enclosed concrete anchors. When installing on a wooden wall take special care as the unit may require extra support to uphold the weight of the plasma display. When installing, please wear working gloves. Be sure that no one is around to distract you during the installation process. When installing, please have at least two people. Please choose a wall that is straight so that the plasma display can be securely attached onto the wall. Place a protective covering over the surface you will be working on when handling the plasma display and the wall hanger units. *PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING (If done with bare hands, it may result in injury) (It may result in injury to you or others) (If attached on an unstable wall, the unit can fall and break) (Because of its weight, the unit may fall and can cause injury) (Failing to do so may result in unwanted marks on the unit) After installing, please be sure to check to see if the unit has been secured firmly. *PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING It is important to use the paper pattern plan to choose the proper place; otherwise, it can result in damage to the wall and you will not be able to install the unit If proper spacing is not allowed, it may cause the plasma display to overheat, which can cause fire or damage to the unit When installing, please use the size referenced below to choose a place, and attach the paper pattern plan to the wall. When installing, please allow at least 15 cm at the top, bottom, left and right on the wall, and clear all items away from where the unit will be. 519.5 .Measurement unit : mm 519.5 314314 15cm 15cm15cm 15cm Paper pattern plan 5 PLASMA DISPLAY HANGER UNIT 6 H W A A N L G L E R UNI T 3. ASSEMBLING INSTRUCTIONS PREPARATION WHEN THE PLASMA DISPLAY IS ATTACHED TO THE STAND TO DETACH THE STAND FROM THE PLASMA DISPLAY TO PLACE THE PROTECTIVE CAPS .To avoid unwanted marks on the unit, place a protective covering over the surface you will be working on and lay the plasma display as shown below. .Unscrew the secured 2 screws completely and Pull the stand away from the plasma display to detach. .There will be two holes where the stand has been detached. .Put the protective caps on the holes and use the screws to secure tightly. 1 2 Screws Caps Holes 7 INSTALLING THE WALL FRAME SET A ON THE PLASMA DISPLAY PANEL HOW TO INSTALL FRAME SET A ON THE UNIT .To avoid unwanted marks on the unit, place a protective covering over the surface you will be working on and lay the plasma display as shown in the picture below. .When securing frame set A to the plasma display panel, make sure that they match the . holes correctly. If the holes are matched incorrectly...