Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Toshiba Dateigröße: 4.31 mb Dateiname: Unterrichtssprache:

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR. 4. See Chapter 5 for details on setting up the TV Guide On Screen system. 5. See Chapter 7 for details on using the TV Guide On Screen system. 18 18 Copyright © 2004 TOSHIBA CORPORATION. All rights reserved. H94(E)012-25(2B-Cnct) 18 8/3/04, 3:41 PM (E) 51/57H94 Chapter 2: Connecting your TV Connecting an HDMI™ or a DVI device to the HDMI input The HDMI[1] input on your TV receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI[2] device. This input is designed to accept HDCP[3] program material in digital form from EIA/CEA-861/861B–compliant[4] consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output). The HDMI input is designed for best performance with 1080i high-definition video signals, but will also accept and display 480i, 480p, and 720p signals. NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC). THIS TV IS NOT INTENDED FOR USE WITH A PC. To connect an HDMI device, you will need: • one HDMI cable (type A connector) For proper operation, it is recommended that you use as short an HDMI cable as possible. You should not encounter difficulty if you use an HDMI cable shorter than 16.4 ft (5m). HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below). Some CDVs (video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. However, if you connect analog audio cables with this connection, the HDMI terminal on the TV will not receive the HDMI digital audio signal and you will hear analog audio only. See “Setting the HDMI audio mode” on page 50. HDMI device L R L R IN OUT HDMI OUT VIDEO AUDIO TV OUT IN AUDIO IN S-VIDEO VIDEO 1 VIDEO 2 L R OUT 1 G-LINK HDMI IN DIGITAL AUDIO OUT TheaterNet ANT (75 ) ANT1 (CABLE) ANT2 CableCARD™ COLOR STREAM HD-1 COLOR STREAM HD-2 VAR AUDIO R L TheaterNet OUT 2 1 2 S-VIDEO IEEE1394 EJECT L/ MONO AUDIO VIDEO R L/ MONO AUDIO VIDEO R L/ MONO AUDIO VIDEO R PB PR Y L AUDIO R PB PR Y L AUDIO R [1] HDMI = High-Definition Multimedia Interface. [2] DVI = Digital Video Interface. [3] HDCP = High-bandwidth Digital Content Protection. [4] EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV. NOTE: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures: •When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device. •When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV. To connect a DVI device, you will need: • one HDMI-to-DVI adapter cable (HDMI type A connector) For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m). • one pair of standard analog audio cables An HDM I-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration below). See “Setting the HDMI audio mode” on page 50. DVI device OUT IN AUDIO IN S-VIDEO VIDEO 1 VIDEO 2 L R OUT 1 G-LINK HDMI IN DIGITAL AUDIO OUT TheaterNet ANT (75 ) ANT1 (CABLE) ANT2 CableCARD™ COLOR STREAM HD-1 COLOR STREAM HD-2 VAR AUDIO TheaterNet OUT 2 1 2 S-VIDEO IEEE1394 EJECT L/ MONO AUDIO VIDEO R L/ MONO AUDIO VIDEO R L/ MONO AUDIO VIDEO R PB PR Y L AUDIO R PB PR Y L AUDIO R VIDEO AUDIO L R L R R IN OUT DVI/ HDCP OUT TV HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. Copyright © 2004 TOSHIBA CORPORATION. All rights reserved. 19 H94(E)012-25(2B-Cnct) 19 8/3/04, 3:42 PM (E) 51/57H94 Chapter 2: Connecting your TV Connecting a digital audio system The TV’s DIGITAL AUDIO OUT jack outputs a or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby Digital decoder or other external audio system with optical audio input. You will need: • one optical audio cable To control the audio: Turn on the TV and the digital audio device. Press MENU on the TV’s remote control and open the AUDIO menu. Highlight AUDIO SETUP and press ENTER. In the OPTICAL OUTPUT FORMAT field, select either DOLBY DIGITAL or PCM, depending on your device (see “Selecting the optical audio output format” on page 83). Audio Audio Settings Advanced Audio Settings Audio Setup Turn off the TV’s built-in speakers in the same AUDIO SETUP menu (above). Also see “Turning off the built-in speakers” on page 83. Connecting an analog audio system This connection allows you to use external speakers with an external audio amplifier to adjust the sound level. You will nee...

Herunterladen

Geben Sie zwei Ziffern: