Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 4.66 mb Dateiname: Unterrichtssprache:

After selecting Yes, press ENTER to have the WS-48413, WS-55413 or WS-65413 go to the Learn menu to start learning the device. NOTE: If you connect a cable box with an RF output other than channel 3, please see the Channel Edit Menu on page 45. 36 Figure 13. NetCommand® IR Menu, Language NetCommand IR Device Setup menu CbCEC(AV Receiver) i Y CabCe i N Cam (corder) i N DBS (Satellite) i N VCR Other CONTINUE SETUP (press ENTER) Select Yes if you have the device, No if not. Press ENTER to configure the device. Figure 14. NetCommand® IR Device Setup Menu SETUP Menu: NetCommand® IR [Device]Learn Menus (WS-48413, WS-55413, WS-65413) NOTE: You will need both the television remote and the device’s remote to perform the Learn Menu functions. 2. NetCommand IR [Device] Learn Menu ,NET (dtmgftd O o [Q [O □ U □ u u NetCommand1"'' IR AVR Learn menu POWER(ON) DIG! POWER OFF MUTE VOLUME UP VOLUME DOWN Rename INPUT 1 | m\ INPUT INPUT 2 INPUT INPUT 3 ^ INPUT INPUT 4 ^ INPUT Continue Setup(press ENTER) DIGITAL/ANALOG MUTE Rename Input INPUT 1 INPUT 2 INPUT 3 INPUT 4 Press ENTER to learn POWER key for AV Rec. Press POWER on AVRec remote until * shows. To check, press POWER key on TV remote. Figure 15. AVR (AVReceiver) Learn Menu Press ENTER to learn POWER key for Cable. Press POWER on Cable remote until * shows. To check, press POWER key on TV remote. Figure 16. Cable Learn Menu NetCommand IR AVR Learn Menu (Figure 15) NetCommand IR Cable (DTV, DBS Learn Menu (Figure 16) NetCommand IR DVD Learn Menu (Figure 17) NetCommand IR VCR Learn Menu (Figure 18, page 38) On the NetCommand IR [Device] Learn menu, for each control (Power, Volume, etc... ) on the NetCommand IR [Device] Learn Menu, use the Adjust buttons on the TV remote to highlight the control you want the TV to learn. Depending on the device, different control buttons will be available. Press ENTER to have the TV highlight and prepare to learn the device’s individual control button. The highlighted button will start flashing. While it flashes, press the corresponding button on the device’s remote. An asterisk (star) will appear on-screen next to the control button name when the code is learned. To verify, press the POWER button on the TV remote to see if the device responds. After the device responds, press ENTER to return to the NetCommand IR Device Setup Menu to select the next device to learn. (o Q □ □ O (□ (□ Q □ (□ Q O a o Learn menu SKIP FRWD SKIP BACK ADJUST UP ADJUST DOWN Press ENTER to learn POWER key for DVD. Press POWER on DVD remote until * shows. To check, press POWER key on TV remote. Figure 17. DVD Learn Menu When all the devices are learned, select CONTINUE SETUP (ENTER) on the NetCommand IR Device Setup Menu to go to the NetCommand IR Assignment Menu. NOTE: If the asterisk does not appear, start the learning process again. If it does not work, your device may not be compatible to be “learned” by NetCommand. NOTE: To deselect an individual control button after it has been learned, use the Adjust buttons to highlight it, then press CANCEL on the TV remote. 37 SETUP Menu: NetCommand® IR Input Assignment and Device Selection Menus (WS-48413, WS-55413, WS-65413) NOTE: You will need both the television remote and the device’s remote to perform the Learn Menu functions. 3. NetCommand IR Input Assignment Menu (Figure 19) After learning all the individual control buttons for each device, you can change the input that each device is connected to. After selecting Continue Setup (press ENTER) on the NetCommand IR Device Setup menu screen, the NetCommand IR Input Assignment Menu will display. You may assign the Device to the TV or AV Receiver input at this screen. Selecting the correct inputs allows the TV to correctly switch devices. An AV Receiver typically has 4 inputs. If all inputs have been assigned, N/A will appear and that input cannot be chosen. After assigning the correct DEVICE and AVREC inputs, press HOME or MENU on the TV remote to return to TV viewing. NOTE: To program the TV’s remote control for NetCommand, hold the Power button while entering the code 935. Device Selection Menu (Figure 20) If your selection was Yes in the NetCommand IR Device Setup Menu (page 36), the device name will appear in the Device Selection Menu. This menu displays on-screen when you press DEVICE on the TV’s remote control. A button appears next to the highlighted, selected device name. Press ENTER to use that device.If audio is through the AV Rec, you will see an icon, if there is not an icon, the audio is through the TV speakers. You may select the device whether or not the NetCommand IR Setup Menu has been enabled. Press ENTER to learn POWER key for VCR. Press POWER on VCR remote until * shows. To check, press POWER key on TV remote. Figure 1S. VCR Setup Menu For each TV input, select connected device and AVR input or turn the input off._ Figure 19. NetCommand IR I...

Herunterladen

Geben Sie zwei Ziffern: