Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 4.1 mb Dateiname: Unterrichtssprache:

Do not use the beater brush section on the grill cloth. General Cleaning Warnings: • DO NOT allow liquid to enter the TV through the ventilation slots or any crevice. • DO NOT use any strong or abrasive cleaners as these can scratch the surfaces. • DO NOT use any cleaners with ammonia, bleach, alcohol, benzine, or thinners as these can dull the surfaces. • DO NOT spray liquids or cleaners directly on the TV’s surfaces. • DO NOT scrub or rub the TV harshly. Wipe it gently. IMPORTANT I I IMPORTANT I DO NOT use any kind of abrasive or liquid cleaner on the surface of the TV I screen or Diamond Shield. | , For further information, please call Consumer Relations at: | 800-332-2119 68 Appendix E: Diamond Shield™ Installation and Removal for Models WS-48313, WS-55313 and WS-65313 Follow the steps below to install and remove the Diamond Shield. INSTALLATION A. Begin by inserting the shield, sliding it into the channels, starting at the bottom. Gently bow the Diamond Shield toward you and insert the Diamond Shield into the top channel. B. Install the left and right molding clips by pressing them into the opening starting at a corner. Do not force the clip. The clip will slide into place. This completes the Diamond Shield installation. REMOVAL To remove the Diamond Shield, reverse the order of the above procedure. Diamond Shield Installation WARNING Sharp edges! Always wear gloves to handle, lift and install Diamond Shield and molding clips. | | IMPORTANT | Molding Clips The Diamond Shield on the WT-42313 is not designed to be removed by the customer. 69 Cabinet Separation for Model WS-65313 Instructions for Separating the Upper and Lower Section of the Projection Television Cabinet For Mitsubishi Dealers and Service Personnel ONLY This Mitsubishi projection television cabinet has been assembled in two pieces. These pieces may be separated to allow for easier delivery and setup. IMPORTANT This projection television weighs over 320 pounds and has many sensitive components. Any dismantling procedure should be done by authorized Mitsubishi Dealers or Service Personnel ONLY. The following operations should be performed by two people: ^ Remove the decorative Plastic Covers (2) on each side of the cabinet and then remove the exposed screws (2) on each side. M Carefully lift the Cabinet-Top straight up until the brackets are clear from the Cabinet-Bottom. DO NOT use the Screen Frame when lifting the Cabinet-Top. ^ Carefully place the Cabinet-Top on to the floor. ^ Once you have moved and positioned the Cabinet-Bottom to its desired location, reverse the procedure and mount the Cabinet-Top on the Cabinet-Bottom. Be sure you align the brackets properly. Keep fingers clear of all joints! Replace the screws and the decorative Plastic Covers that were removed in Step|a] 70 Terminal Cover Ventilation for Model WT-42313 Wall AIR CIRCULATION TIP When considering the location or position of your TV, we recommend you place it at least 2” (inches) away from the wall. Like most electrical equipment and appliances, better air circulation allows your television to run cooler, assuring a long, trouble-free life. At Least 2” (Inches) Away from Wall SIDE PANEL FOR INPUT TERMINAL Included in the accessories bag is the side panel to cover the input terminals, located on the bottom right of your TV. See diagram. Follow the steps below to attach or remove this side panel: 1. Remove the side panel from the accessories plastic bag attached to the back of your TV. 2. Route all of the cable downward so the cover can close over them. 3. Position the three tabs directly opposite the three slots (see diagram) and gently push toward the front of the TV. 4. Slide the two push tabs into the slots on the other side of the terminals until both tabs snap into place. Push Tabs Result: The side panel neatly covers the input jacks. Reverse these steps to remove the side panel from the input terminal. STAND REQUIREMENT Slots CAUTION: This PTV for use only with Mitsubishi stand MB-42311. Use with other stands is capable of resulting in instability causing possible injury. 71 Index A A/V Memory Reset 55 Receiver, Connecting 17 Activating the PIP and POP 29 Advanced Convergence Menu 53 Advanced Features Menu 34, 50-54 Antenna Channel Edit Menu 42 Connecting 14, 15 Appendices A: Bypassing the V-Chip Lock 63 B: High Definition Input Connection Compatibility 65 C: Remote Control Programming Codes 66 D: Cleaning and Service 68 E: Diamond Shield™ Installation and Removal for Models WS-48313, WS-55313 and WS-65313 69 Audio/Video Settings Menu 34, 55 A/V Memory Reset 55 Audio Output 55 TV Speakers 55 Audio Settings Menu 55 Audio Settings Description 56 Automatic POP Switching 62 Auto Color Correction Menu 50 Available On-Screen Format Sizes 60 B Back Panel Input/Output for WS-48313, WS-55313 & WS-65313 11 Black Enhancement Menu 54 Bypassing the V-Chip Lock 63 C Cabinet Separation for Model WS-65313 7...

Herunterladen

Geben Sie zwei Ziffern: