Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
This appliance must only be plugged into an earthed mains socket • The electrical plug on the mains cable must be unplugged from the mains socket before filling or emptying the water tank • Do not leave the iron unattended while it is plugged in. Should you have to leave the area where you are ironing, unplug the iron from the mains socket • Never plug the appliance into the mains supply if the cable or the appliance itself show visible signs of damage. Unplug the appliance from the mains supply after each use or if a fault is suspected • Any works or repairs that the appliance may need, e.g. replacing a faulty mains cable, must only be carried out by qualified personnel from an authorised technical service centre • Never immerse the iron in water or any other liquid • Keep the appliance out of the reach of children. Electric irons reach high temperatures and produce hot steam during use, so take special care not to burn or scald yourself • Danger of electric shocks or fire • The iron has a built in safety cut-out device which switches it off should it malfunction • Never leave a hot iron standing on textiles or on the mains cable. Make sure it is completely cold before storing it away. Do not unplug it by tugging on the mains cable or leave the plug hanging freely • We accept no responsibility for any damage caused as a result of misuse or improper use resulting from not following the instructions in this manual • When using the iron for the first time it may produce certain vapours and odours that will die away after a few minutes Filling the water tank • Unplug the iron •Set the steam selector to the “0” ( ) position (no steam) • Place the iron at an angle of 45. B TDA 24…(2) Instructions for use • Fill the tank but never above the “max” mark • Only use clean tap water, without any type of additive. Any other type of liquid could damage the appliance • To obtain better and longer steam production mix tap water with distilled water in the measures shown in the table below. Using distilled water as recommended in these instructions will also help to prolong the life of your iron if you live in a hard water area Water hardness level Amount of distilled water / tap water Very soft / soft 0 / 1 Average 0 / 1 Hard 1 / 1 (approx.) Very hard 2 / 1 (approx.) Setting the temperature • Check the temperature instructions shown on the care label of the garment you are ironing and set the temperature control to the corresponding position: «•» ............................ Synthetics «••» .......................... Silk - Wool «•••» ........................ Cotton - Linen • If you are not sure what type of material the garment is made from, start ironing on the lowest temperature setting • Sort your garments based on their care labels, always starting with clothes that have to be ironed at the lowest temperature • The pilot lamp will stay lit while the iron is heating up and go out once the selected temperature has been reached. Wait a few seconds after the lamp goes out before you start ironing. Once the iron is hot you can continue to iron even if the pilot lamp comes on again Ironing with steam After Sales Service Great Britain BSH Appliance Care Grand Union House Old Wolverton Road Milton Keynes MK12 5ZR +44 (0)8705 678910 B • Make sure that there is water in the tank • Turn the temperature selector to the steam “ ” area between “••” and “max” 001TDA24..(2)GB /11/04 min max Synthetics Silk-Wool Cotton-Linen min max Synthetics Silk-Wool Cotton-Linen 0 2 1 0 2 1 • Set the steam regulator to the appropriate setting: - Set the steam regulator to the “1” position for “••” temperature setting - Set the steam regulator to the “2” position for “•••” and “max” temperature settings Ironing without steam •Set the steam regulator to the “0” ( ) position • Select an appropriate temperature for the type of material being ironed Spray • Make sure that there is water in the tank • Press the spray “ ” button Vertical steaming with jet of steam • Never spray or aim steam at people ! • Set the temperature control to the “•••” or “max” position • Hold the iron in an upright position 10-20 cm away from the object being steamed • Press the jet of steam “ ” button at intervals of 5 seconds Ironing with jet of steam • Set the temperature control to the “•••” or “max” position • Press the jet of steam “ ” button repeatedly at intervals of 5 seconds Additional features: (dependent on model) Anti-drip system If your iron is equipped with an anti-drip system, it will automatically stop producing steam when the selected temperature setting is too low. You may hear a clicking sound when this system is in operation Anti-scale system If your iron is equipped with an anti-scale system, this will reduce the build up of lime scale, consequently prolonging the life of the appliance. However, this system does not completely prevent the formation of lime scale. Please read the “After finishing each ironing session” section of t...