Stimmen - 6, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: JVC Dateigröße: 2.96 mb Dateiname: Unterrichtssprache:

For Best Results from the Remote Control: • Be within 20 feet of the equipment. • Do not press two or more buttons at the same time unless instructed to. • Do not allow to get wet or become heated. • Avoid dropping on hard surfaces. • Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth. • Do not mix new and old batteries. • Do not heat, take apart, or throw batteries into fire. • Use only AAA batteries. Operating the Remote Control: You can use the remote to control the TV, CABLE/DBS/ DTV, VCR, DVD, and AUDIO products. Select the product you want to control by moving the slide switch to the appropriate position. The remote control has been preset to operate the TV and other Mitsubishi products. To program the remote control to operate other products, see Use of the Remote Control with Other A/V Products, page 25. POWERINFOPAUSERECFF/FWDREW/REVPLAYSTOP369QVVOLUMEGUIDEEXCHENTERCANCELMENUV-CHIPFORMATPIPCH17SQV4INPUTSLEEPVIDEOAUDIOMUTE2580CHANNELADJUSTPIPINPUTPIP/POPHOMETVAUDIOCABLE/DBS/DTVDVDVCR 1 2 3 6 4 5 10 7 11 8 9 12 31 13 15 14 17 16 21 19 18 20 24 23 22 26 25 27 30 28 29 Figure 1. Remote Control Functions. sizeAAAbatteriesAAAAAA Figure 2. Installing the batteries. The remote control may return to its initial setting when the batteries are changed. It may need to be reprogrammed. Remote Control Functions: Channel Selection, Sleep Timer POWER369QV 17SQV4SLEEP 2580 TVAUDIOCABLE/DBS/DTVDVDVCR Channel Selection • Enter three numbers (for channel 2, press 002). or • Press the channel number and ENTER (for channel 2, press 2, then ENTER). or • Enter the channel number and wait four seconds (without pressing ENTER). The TV will change automatically. Note: Use the CANCEL button for digital subchannel (-) selection in the CABLE/DBS/DTV layer. Figure 3. Sleep button on remote control Sleep Timer (Figure 3 & 4) Setting the Sleep Timer: • Press SLEEP on the remote control. • A message indicating the length of time the sleep timer is to be set appears on the TV screen. • Each press of SLEEP will increase the time displayed by 30 minutes, until the maximum value of 120 minutes is reached. • After 5 seconds of inactivity, the message will disappear. • Press SLEEP to view the remaining time before the timer turns the TV off. Canceling the Sleep Timer: • Press the SLEEP button to display the on-screen message. • Press SLEEP repeatedly until OFF is displayed. After 5 seconds of inactivity, the message will disappear. Sleep: 30 min. Figure 4. On-screen display for sleep timer Use of the Remote Control with Other A/V Products Programming the Remote Control to Use with Other Brands of Audio and Video Products: (Figures 1-4 this page, Figure 5, following page) 1. Move the slide switch at the top of the remote to the product you want to control. 2. Press and hold the POWER button on the remote control. 3. Enter the first three digit code listed for your equipment, and then release the POWER button on the remote control. 4. Point the remote control to the equipment and press the POWER button. Note: If the equipment responds,the remote control is properly programmed to operate the equipment. If the equipment does not respond, repeat steps 2-4 with the next three digit code listed in step 3. POWERCodetoenter: Toresettodefaultcode,enter000VCRbrandMitsubishiHitachiJVCPhillips/MagnavoxPanasonicRCASonyToshiba001,002020,043,065030,054043,044,051041,042,043020,053,065048,049,050021IfyourVCRcodeisnotlistedhere, pleaseseepage61foracompletelisting. VCRCodes1.2.3. TVAUDIOCABLE/DBS/DTVDVDVCR POWERCodetoenter: Toresettodefaultcode,enter000CableboxbrandGeneralInstruments/ JerroldMotorolaOakPioneerScientificAtlantaZenith119,120,121,122,123,124125,126,127139,137,102101,116112,113117,100Ifyourcableboxcodeisnotlistedhere, pleaseseepage60foracompletelisting. CableBoxCodes1.2.3. TVAUDIOCABLE/DBS/DTVDVDVCR Figure 1. Programming the remote to control your cable box. Figure 3. Programming the remote to control your VCR. When set to TV, the PLAY, STOP, REW/ REV, and FF/FWD buttons will operate the VCR after the VCR codes have been properly programmed into the remote control. If you cannot turn the cable box ON by pressing POWER, try pressing CHANNEL or the number buttons. POWERCodetoenter: Toresettodefaultcode,enter000SatellitebrandMitsubishiDTV-DBSDishNetworkHughes-DBSPanasonic-DBSRCA-DBSSony-DBSToshiba-DBS006175173174176177170,173,189,190,191Ifyoursatellitereceivercodeisnotlistedhere, pleaseseepage61foracompletelisting. SatelliteReceiverCodes1.3.2. TVAUDIOCABLE/DBS/DTVDVDVCR POWERCodetoenter: Toresettodefaultcode,enter000DVD/LDPbrandMitsubishiJVCPanasonicPhilipsPioneerDVDSamsungSonyToshiba003257250258,253,272252261254253IfyourDVDcodeisnotlistedhere, pleaseseepage60foracompletelisting. DVDPlayerCodes1.2.3. TVAUDIOCABLE/DBS/DTVDVDVCR Figure 2. Programming the remote to control your satellite receiver. Figure 4. Programming the remote to control your DVD or LDP. Use of the Remote Control with Other A/V Products, continued POWER...

Herunterladen

Geben Sie zwei Ziffern: