Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 2.96 mb Dateiname: d66cce81-0a28-4b4d-8dd5-fc611e234230.pdf Unterrichtssprache:

.................................................................................................................................................................................................................................................................................. Figure 1. Connecting separate UHF and VHF antennas. Figure 2. Connecting twin lead antenna, coaxial lead antenna, or wall outlet cable. Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable. Additional connection cables are not provided with the TV. They should be available at most electronic stores. Connecting an Antenna to a Cable Box or VCR Antenna to a VCR (Figure 4) 1. Connect the incoming cable to ANT-A on the TV back panel. Connect two coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to ANTENNA IN on the VCR back panel. 3. One from VCR back panel ANTENNA OUT to ANT- B on the TV back panel. Note: If your VCR has separate audio/video outputs, connect the audio as shown in Figure 6, page 14. Antenna to a Cable Box (Figure 3) 1. Connect the incoming cable to ANT-A on the TV back panel. Connect two coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the cable box back panel. 3. One from OUT on the cable box back panel to ANT- B on the TV back panel. Note: If your cable box has separate audio/video outputs, connect the audio as shown in Figure 6, page 14. ............................................................................................................................................................................................................................ .................................................................................................................................................................................................................................................................................... Figure 4. Connecting the VCR with antenna or wall outlet cable. Figure 3. Connecting the cable box. Note: When the Energy Mode is set to Low, the VCR may not record programs when the TV is off. Note: For digital cable boxes, refer to your Digital Cable Box owner’s guide for instructions on optimal connections to this TV. Connecting an Antenna to a Cable Box and VCR, Connecting Composite Video or S-Video with Audio Composite Video or S-Video (Recommended) with Audio (Figure 6) 1. Connect a video or an S-Video cable from VIDEO OUT on the VCR back panel to VIDEO or S-VIDEO, INPUT-1 or INPUT-2 on the TV back panel. 2. Connect a set of audio cables from AUDIO OUT on the VCR back panel to AUDIO INPUT-1 or INPUT-2 on the TV back panel, matching the input used in step 1. • The red cable connects to the R (right) channel • The white cable connects to the L (left) channel If your VCR is mono (non-stereo), connect only the white (left) cable. You may connect to the S-VIDEO or VIDEO terminal but not to both. Contact your local cable or satellite provider or refer to the cable box or satellite Owner’s Guide for instructions on optimal connections to this TV. Antenna to Cable Box and VCR (Figure 5) 1. Connect the incoming cable to ANT-A on the TV back panel. Connect three coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the back of the cable box. 3. One from OUT on the back of the cable box to ANTENNA IN on the VCR back panel. 4. One from ANTENNA OUT on the VCR back panel to ANT-B on the TV back panel. Note: For best performance, connect the audio as shown in Figure 6, page 14. AUDIOOUTAUDIOINVIDEOOUT(Y/C) MONITOR1LRLR12CableboxorVCRbackpanelAttachonlyonecabletype1Attachonlyonecabletype122WhiteRedWhiteRedTVbackpanel(sectiondetail) INPUT21AUDIO- RIGHTAUDIO- LEFT/ (MONO) VIDEOS-VIDEOMONITOROUT(Recommendedifavailable) 1 ...................................................................................................................................................................................................................................................................................................................... Figure 6. Connecting Composite Video and Audio. Figure 5. Connecting the VCR with cable box. Additional connection cables are not provided with the TV. They should be available at most electronic stores. Connecting a Stereo Audio System Conecting an Audio Receiver Stereo Audio System (Recommended for shelf units or A/V receivers without digital audio inputs) (Figure 7) 1. Connect the audio cables from AUDIO MONITOR OUTPUT on the TV back panel to TV IN or AUX IN terminals on the back of the audio system. • The red cable connects to the R (right) channel • The white cable connects to the L (left) channel 2. Use the AUDIO/VIDEO SETTINGS menu (page 50) to turn off the TV’s speakers. 3. Set the input of the audio system to the TV or AUX position to hear ...

Herunterladen

Geben Sie zwei Ziffern: