Login:
Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Peerless Industries, modell OneMount RTONES

Hersteller: Peerless Industries
Dateigröße: 1.58 mb
Dateiname:

Unterrichtssprache:enesfr

Das Dokument wird geladen, bitte warten
Das Dokument wird geladen, bitte warten

Anleitung Zusammenfassung


The top mounting hole should be 2.5" above the desired screen center as shown in figure 4.1 on page 8. Drill four 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (EE) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (DD). Level, then tighten all fasteners. NOTE: Six holes and six sets of fasteners are required when mounting the wall plate for equipment weighing greater than 200 lbs. • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. WARNING CUTAWAY VIEW INCORRECT concrete surface 1 3 2 EE Drill holes and insert anchors (EE). CORRECT Place plate (AA) over anchors (EE) and secure with screws (DD). Tighten all fasteners. wall plate plaster/ dry wall concrete wall plate concrete plaster/ dry wall • Always attach concrete anchors directly to loadbearing concrete. • Never attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. (Not evaluated by UL) WARNING AA • Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). WARNING DD AA DD EE EE solid concrete cinder block 11 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Mounting and Removing Flat Panel Screen Adjust tension knobs shown in detail 2 to desired tension, balancing your screen size and weight. The tension knob, without changing the bracket tension, can be pulled out, away from the bracket and turned independently of the knob post for readjustment as shown in Detail 3. Push or pull from top or bottom of screen to adjust tilt as shown in figure 6.1. The tilt can be adjusted to a maximum of 15° forward or 5° backward. NOTE: To lock the screen into the desired tilt position, use locator hole to find tilt position hole. Tighten IncreLok™ tilt locking screws on both tilt brackets as shown in figure 6.1 and detail 2. Adjusting the Tilt Angle of the Flat Panel Screen • Be careful not to pinch fingers when pushing screen from the bottom. CAUTION BB and CC AA DETAIL 1 AA DETAIL 2 fig 6.1 SAFETY SCREW IncreLok™ TILT LOCKING SCREW LOCATOR HOLE TENSION KNOB fig 5.1 fig 5.2 © 2006 Peerless Industries, Inc. All rights reserved. Onemount is a trademark and Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners. TILT POSITION HOLES CS = center of screen DETAIL 3 TENSION KNOB NOTE: For security, replace safety screw in each tilt bracket with M5 x 30 security screw (HH) using wrench (II). Adjust brackets to full back tilt position and tighten. Hook tilt brackets (BB and CC) onto wall plate (AA). Then slowly swing screen in as shown. Turn safety screws, using wrench (II), clockwise till fully tightened down and screw tip securely contacts bottom of the wall plates as shown in detail 1. of figure 5.1. Center of screen can be adjusted horizontally no more than 4" from center of the wall plate configuration, if desired as shown in figure 5.2. NOTE: To lock the screen down, tighten safety screws to wall plate using a wrench (II) as shown in detail 1. To remove screen from mount, loosen safety screws, swing screen away from mount, and lift screen off of mount. 4" • Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque. CAUTION • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. WARNING Modelos: ONE-TP, ONE-TP-S, RTONE, RTONES 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • Maxima capacidad de carga UL 250lb (113.5kg) Instalacion y Ensamblaje: OneMount™ Este producto esta inscripto en la Lista UL. Debe ser instalado por un instalador profesional cualificado. Caracte...

Dieses Handbuch ist für folgende Modelle:
Fernseher - OneMount ONE-TP-S (1.58 mb)
Fernseher - OneMount RTONE (1.58 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien