Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Peerless Industries Dateigröße: 1.58 mb Dateiname: Unterrichtssprache:

CENTER BRACKETS VERTICALLY ON BACK OF SCREEN X CC X Note: "X" dimensions should be equal. KNOBS FACE OUT BB fig 2.1 NOTES: • Always use multi-washers when attaching tilt brackets (BB and CC) to your screen when using small, medium or large screws. No multi-washer is required for extra large (M8) screws. • Use the corresponding hole in the multi-washer that matches your screw size as shown in fig 2.2. MULTI-WASHER fig 2.2 MEDIUM HOLE FOR M5 SCREWS LARGE HOLE FOR M6 SCREWS SMALL HOLE FOR M4 SCREWS NOTE: For flat back screens proceed to step 2-3. For bump-out or recessed back screen skip to step 2-4 5 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 For Flat Back Screen For Flat Back Screen Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws. NOTE: Spacers may not be used, depending upon the type of screen. If you have any questions, please call Peerless customer care at 1-800-729-0307 or visit our website at to locate your screen compatibility chart. ADAPTER BRACKET (BB or CC) SCREEN fig 2.3 MULTI-WASHER SCREW For Bump-out or Recessed Back Screen Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws. If you have any questions, please call Peerless customer care at 1-800-729-0307 or visit our website at to locate your screen compatibility chart. SCREEN MULTI-WASHER SCREW ADAPTER BRACKET (BB or CC) fig 2.4 SPACER 6 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 7 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 With tape measure, measure the outside to outside of the brackets on the back of your screen. If width of the tilt brackets on back of the screen is over 18-1/2" shown in figure 3.1, using a 7/16" wrench, attach wing bracket (GG) to center bracket using two 1/4" serrated flanged locknuts (FF) as shown in figure 3.2. If width of the brackets on back of the screen is over 30-3/8", using a 7/16" wrench, attach second wing bracket (GG) to center bracket using two 1/4" serrated flanged locknut (FF) as shown in figure 3.3. CAUTION: If mounting to two studs on 16" centers, and using the three plate configuration, A STUD MUST BE SKIPPED in the middle so distance between studs is 32". AA 18.5" fig. 3.1 fig. 3.3 FF AA GG fig. 3.2 AA GG FF 8 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Installation to Double Wood Stud Wall NOTE: If mounting equipment weighing greater than 200 lbs, triple stud mounting is strongly recommended. Skip to page 9 Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen center as shown in figure 4.1. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 4.2. NOTE: Wall plate may be mounted up to 4" (102 mm) off center as shown in figure 4.1. Skip to step 5. • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended. • Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations. WARNING fig. 4.1 4" (102 mm) 4" (102 mm) DD AA fig. 4.2 CS = center of screen STUD AA 2.5" (64 mm) CS 9 of 33 ISSUED: 09-20-06 SHEET #: 202-9167-3 01-26-07 Installation to Triple Wood Stud Wall CS = center of screen fig. 4.3 4" (102 mm) 4" (102 mm) Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to ...

Herunterladen

Geben Sie zwei Ziffern: