Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
However, channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the TV/DVD/VCR Remote Control. Unattended timer recording is limited to one channel at a time. Antenna/Cable Connections Continued on the Next Page. - 11-EN 1C29 TO RECORD A SCRAMBLED/UNSCRAMBLED CHANNEL 1. Set the TV/DVD/VCR channel selector to the output channel of the Cable Converter Box or Satellite Box. (Ex. CH3) 2.Select the channel to record from your Cable Converter Box or Satellite Box. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. CONNECTING TO EXTERNAL INPUT JACKS When you watch a program recorded on an another source (VCR or video camera), use the audio/video input jacks on the front of the TV/DVD/VCR. Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks of this TV/DVD/VCR. Then press the CHANNEL buttons K/L until "AUX" appears on the screen. NOTE: • When you connect a monaural VCR (another source) to this TV/DVD/VCR, connect the Audio output jack of the monaural VCR (another source) to the AUDIO L jack of this TV/DVD/VCR. The audio will output in both L and R channel equally. To the audio L-AUDIO-RVIDEOHEADPHONE [Another source] output jacks Audio/Video coaxial cable (not supplied) etc. To the video [Front of the TV/DVD/VCR] output jack [Fig. 5] INSTALLING THE BATTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow. 2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings. 3)Replace the cover. EXTERNAL INPUT MODE When using an external input signal (another VCR or video camera), connect the player’s audio/video output cables to the AUDIO L/R IN/ AUX VIDEO IN jacks of your TV/DVD/VCR. Then press the CHANNEL button K or L until “AUX” appears on the screen. - 12-EN 1C29 CONNECTING TO A STEREO SYSTEM CONNECTING TO A STEREO SYSTEM ANT. L 1 To Right (red) and Left (white) AUDIO OUT jacks To ANALOG AUDIO INPUT jacks [Fig. 6] Stereo system NOTES: • Be sure to turn off the power to all components in the system before connecting another component. • Refer to the Owner's Manuals for your stereo system and any other components to be connected to the TV/DVD/VCR. CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD) Use an audio coaxial digital cable available at retail for the audio connections. Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck. ANT. L AUDIO OUT R COAXIAL 1 Amplifier equipped with digital input jacks, MD deck, DAT deck, etc. To COAXIAL DIGITAL AUDIO INPUT jack To DIGITAL AUDIO OUT (PCM/BITSTREAM) COAXIAL jack (only DVD AUDIO OUT) [Fig. 7] NOTES: • The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck. • Be sure to turn off the power to all components in the system before connecting another component. • Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR. • Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may also damage the speakers. - 13-EN 1C29 CONNECTING TO A DOLBY DIGITAL DECODER (for DVD) CONNECTING TO A DOLBY DIGITAL DECODER (for DVD) If using this TV/DVD/VCR to play a DVD disc in a 5.1 channel Dolby Digital surround format, the TV/DVD/VCR outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the player up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as enjoyed in movie theaters. Use audio coaxial digital cables available at retail for the audio connections. ANT. L AUDIO OUT R COAXIAL 1Front speaker (left) Center speaker Front speaker (right) Surround speaker (left) Surround speaker (right) Subwoofer To DIGITAL AUDIO OUT (PCM/BITSTREAM) COAXIAL jack To COAXIAL DIGITAL AUDIO INPUT jack Dolby Digital decoder [Fig. 8] NOTES: • Be sure to turn off the power to all components in the system before connecting another component. • Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR. • If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode. (See page 45 to set DOLBY DIGITAL to ON.) • Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may also damage the speakers. Manufactured under license from Dolby Laboratories. ...
Dieses Handbuch ist für folgende Modelle:Fernseher - 6727DD (932.53 kb)