Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
and the Serial No. of your television in the space provided. Model No. Serial No. Keep this information for future use. 0 .J J I I _".; i.o_ ._ SEARS 35" TABLETOP COLOR TELEVISION WITH REMOTE CONTROL Safety Information Use Warranty and Service Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Safety Precautions I IWARNING: To prevent fire or shock hazard, do not [ expose this TV to rain or moisture. CAUTION: Avoid placing drinks or vases with water on top of your TV. If you suspect that liquid has entered the TV, unplug it immediately and contact a Sears Service Center. Turning it off is not enough -your TV has power applied to some circuits even when the TV is turned off. RiSK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash CAUTION: TO REDUCE THE The exclamation jnd arrowhead RISK OF ELECTRIC SHOCK, point within the within the trlangis DO NOT REMOVE COVER tdangIs Is a Is a warning sign (OR BACK). NO USER-warning sign lisrtirlg you of SERVICEABLE PARTS alerting you of "dangerous INSIDE. REFER SERVICING Important voltage" Inside the TO QUALIRED SERVICE Instructions product that PERSONNEL. accompanying the presents a dsk of product. electric shock. CAUTION: Maintain electrical safety. Powerline-operated equipment or accessories connected to this unit should bear the UL listing mark or, if purchased and used in Canada, the CSA certification mark on the accessory itself and should not have been modified so as to defeat the safety features. This will help avoid any potential hazard from electric shock or fire. If in doubt, contact qualified service personnel. Your TV operates on 120 volts, 60 Hz AC power (normal house power) and has a polarized AC plug. Because one blade of the plug is wider than the other, the plug fits into the wall socket only one way. Do not defeat the safety feature of this plug. If you need an extension cord, make sure it is polarized. the polarized plug on this TV with an extension cord, _ CAUTION: To prevent electric shock, do not use receptacle, or other outlet unless both blades can be fully inserted to prevent blade exposure. Match wide blade of plug to wide slot, fully insert. Getting Started First-Time Operation The steps below will help you get your TV connected and 5. Turn on TV, adjust the volume, and select a channel. x,orking quickly. The page numbers on which you can est ttono te find detailed instructions for each of these steps are also listed for your convenience. 1. Unpack TV and accessories. Shown here are the accessories thatcame packed with your TV. An.oa--r Remote Control and Four AAA Batteries Power Cord 2. Install batteries in remote control. Details are on page 6. 3. Connect antenna or cable-TV system. Most antenna or cable-TV systems can be connected as shown here. Back of TV CABLEJ_NTENNA tog Incoming Cable from Antenna or Cable-TV System • Details for connecting a home antenna to your TV are on page 20. • Details for connecting a cable-TV system to your TV are on page 21. • Details for connecting a VCR to your TV are on pages 27-28. 4. Attach power cord. First attach the flat end of the power cord completely into the connector on the back of your TV, and then plug the other end into a wall outlet. Do This Not This e =7CHAN (Channel) Buttons VOL (Volume) Buttons down button to adjust the volume to a desired level. • Press the CHANNEL up or down button to select the next channel in memory. You can also press two number buttons to select a channel. To select a 3-digit cable channel (up to channel 128), press and hold number button 1 until 1-appears on the screen. Then press the other two numbers. Channels 2-13 were programmed into the channel memory for you at the factory, so pressing CHANNEL up or down stops at these channels only. When you start the autoprogramming feature (described in step 6), your set will automatically scan through all channels and place only the active channels for your area into its channel memory. • Details about using the remote are on page 6. 6. AutoProgram the TV's channel memory. To start the TV autoprogramming press the SETUP itself, button t:>O0_ o0b_ repeatedly to select -Bu_on-( highlight) the A UTOPROGRAM _'_'_'_,,_ + Button function, and then press +. Details are on page 16. You can also add and erase channels from memory as desired by first pressing SETUP to select (highlight) the CHAN MEM function. Select the desired channel number by pressing the CHANNEL up.or down button or by pressing the tw_ corresponding number buttons. Then press + to add a channel, or press -to erase a channel. Details are on page 16. Getting Started First-Time Operation (continued) Adjust PICTURE TILT switches if necessary. This model has an extra large color picture tube. The effects of geomagnetism (Earth's magnetic field) may cause the picture to tilt slightly. The POLARITY and STRENGTH POUkRITY STRENGTH switches on the back of the TV let you compensate for this effect. If the picture appears PICTURE TiLT tilted, follow these steps to improve...