Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Not all features (and drawings) discussed in this manual will necessarily match those found with your television set. This is normal and does not require you contacting your dealer or requesting service. 3 4 5 6 7 9 .11 12 13 14 15 17 19 20 21 22 .22 .22 22 .22 22 .22 .23 23 .23 23 .23 24 .25 25 26 .26 .29 .30 .31 .31 31 32 33 .33 .33 .34 .35 36 38 .42 Remote control picture select picture menu sound select sound menu feature select feature menu select external connection select volume level ( O ] not applicable PhT| switch sound mode [ @ ] select "incredible sound" Teletext: on/off Teletext coloured keys -fast select pages select index page display time reveal solution hold sub-pages enlarge page interrupt teletext not applicable reduce picture interference / fol (7) (7) (?) GD (4) (5) Q)f ^CREDIBLE go © © @ / / TXT OWff SOURCE POSITION PROGRAM SCAN (c!>) switch to "stand-by" 0ly confirm your choice *) select your choice select channel [ ] “mute" sound I/® to (s) select digits [ a/ch] select previous channel [ osd) display on screen information "SMART" control : ( picture ) select "SMART" picture ( sound ) select "SMART" sound (§D not applicable INCREDIBLE /—n switch on picture "incredible picture" (Q) switch on subtitle PIP: ON/OFF On/Off PIP source select PIP source position move PIP screen program select PIP channel +/— scan not applicable swap switch PIP screen still freeze PIP screen VCR: (i) stop tape @) rewind tape (•) record onto tape ® forward tape (►) play tape English English Front Controls m MAIN OWER VOL CH A ADV A, ADV T 10 Button no. Function 0 Switch on/off TV. 0 Switch on/off TV from standby. a Dual function a) Increase volume of sound. b) When a menu is active, move cursor to the left. 0 Dual function a) Decrease volume of sound. b) When a menu is active, move cursor to the right. 0 Select a higher channel number. 0 Select a lower channel number. 0 Call up the main menu. 0 Move cursor up in a menu. 0 Move cursor down in a menu. 0 Move to a higher level menu. i I -r Back connection Connect your aerial cable Insert the aerial plug tightly into the aerial socket at the back of the TV with an aerial cable of good quality. Consult your local dealer if you have any queries or need any assistance on connection. nr -m(o ir © cable EXTERNAL 1 Amplifier S3 f ) VCR Laser disc player Connect to power Refer to the specification page for the correct operating voltage. Consult your local dealer if your mains supply is different. • Connect your television to the mains supply socket and switch on. (Diagram is only a representation of the actual plug and socket) Audio Video connection Refer to the section on "Connecting other equipment" at the back of this manual for details. Setting up the remote control and TV Setting up the remote control Remove the battery cover at the back of your remote control. Insert two batteries (Type AAA, 1.5 V) into the compartment. Note: • Remove the batteries from the remote control if you do not use it for an extended period. This is to prevent possible damage due to battery leakage. • Make sure that there is no obstruction between the remote control and the television. • Do not use old and new batteries together. Setting up the TV Press the power knob © button on the front, bottom left of your television. A green or red indicator light appears. 0 MAIN POWER If the indicator light is GREEN, it means: Your television is switched ON. Wait a few seconds for the screen to light up. If no signal input is detected, you will see a blue screen with the word "PHILIPS." If the indicator light is RED, it means: Your television is switched on but the screen stays dark. Your television is on 'standby.' Press any digit button, CH + or — button, A/CH button or VIDEO button on your remote control. The screen lights up. If no signal input is detected, you will see a blue screen with the word "PHILIPS." Note : If there is no signal detected after about 10 minutes, your television will switch over to standby. Before Calling Service Caution: Avoid displaying stationary images on your TV screen for an extended period of time. Stationary patterns generated by the PIP display, computer displays, teletext etc., can become permanently ingrained on the picture tube. This damage is not protected by your warranty as it is a result of misuse. If you need to display still images, it is always advisable to reduce the brightness and contrast settings or alternate with normal TV viewing. Please make these simple checks before calling service. These tips can save you time and money since charges for TV installation and adjustments of customer controls are not covered under your warranty. Symptoms Items to Check and Actions to follow 'Ghosts' or double images or teletext garbled This may be caused by obstruction to the antenna due to high...