Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
3. Refer to the image below and locate DIP #2 on the DIP switch bank. 4. Move DIP 2 to the “ON” position. This will enable Deep Color support and will be used only if the display supports this deep color. NOTE: DIP 1 must be in the “OFF” position in order to enable deep color. 5. Reconnect power to the receiver unit. 9 DIP SWITCH CONFIGURATION DIP SWITCH CONFIGURATION – EDID Under normal circumstances, a source device (digital and analog) will require information about a connected device/display to assess what resolutions and features are available. The source can then cater its output to send only resolutions and features that are compatible with the attached device/display. This information is called EDID (Extended Display Information Data) and a source device can only accept and read one EDID from a connected device/ display. Likewise, the source can only output one resolution for use by a connected device/display. The Extender for HDMI1.3 over one CAT6 uses DIP #1 to control EDID modes. There are 2 EDID modes; LOCAL and PASSTHROUGH. The LOCAL mode will create a new EDID by copying all video and audio features of the connected device but will allow the user to control Deep Color support by the procedure on the previous page. By default, the unit is shipped in LOCAL mode where DIP #1 is in the OFF position. The PASSTHROUGH mode will simply allow all video and audio features of the connected device to pass through to the source device without control over Deep Color support. DIP #1 can be switched to the ON position to enable the PASSTHROUGH mode. However, if DIP #1 is switched to the ON position, enabling Deep Color (DIP #2=ON) will not affect the video features of the EDID. When switching DIP #1 between the OFF and ON position, please follow the procedure outlined below: 1. Disconnect power from the receiver and locate the DIP switch bank on the bottom of the unit. NOTE: You may need to remove the piece of silver colored metallic tape to expose the DIP switch bank. 2. Refer to the DIP switch image (below) and locate DIP #1 on the DIP switch bank. 3. Move DIP #1 to the “ON” or “OFF” position. The “OFF” position will use the LOCAL EDID mode. The “ON” position sets the unit in PASSTHROUGH mode, allowing the source to use the original EDID features of the display. 4. Reconnect power to the receiver unit. 10 NETWORK CABLE WIRING DIAGRAM Gefen has specif cally engineered their products to work with the TIA/EIA-568-B specif cation. Please adhere to the table below when f eld terminating cable for use with Gefen products. Failure to do so may produce unexpected results and reduced performance. Pin Color 1 Orange / White 2 Orange 3 Green / White 4 Blue 5 Blue / White 6 Green 7 Brown / White 8 Brown 12345678 This product was designed for use with CAT-6a (augmented) cabling only. This unit will either not perform to specif cation or refuse to operate completely if cabling other than CAT-6a is used. Each cable run must be one continuous run from one end to the other. No splices or use of punch down blocks. 11 SPECIFICATIONS Video Amplif er Bandwidth ....................................................................... 225 MHz Single Link Max. Resolution ................................................ 1080p/60, 12 bit color Input DDC Signal ......................................................................... 5 Volts p-p (TTL) Input Video Signal .............................................................................. 1.2 Volts p-p HDMI Connector ................................................................ Type A, 19 Pin Female Link Connector .............................................................................. RJ-45 Shielded Power Supply ......................................................................... 5V DC @ 0.6A each Power Consumption ................................................................... 3 Watts (per unit) Dimensions ...................................................................... 3.3” W x 1.3” H x 3.3” D Shipping Weight ............................................................................................ 3 lbs. 12 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notif ed within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modif cations. Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for ninety (90) days from the day of reshipment to the Buyer. This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or f tness for any particular purpose, all of which are expressly disclaimed. 1. ...