Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
The reason for this order is that with the power feeder unit completely assembled, it will be easier to locate where on the table top you will need to drill your base mounting holes, so you can take advantage of the full range of power feeder swing and adjustments. Through-Bolt Mounting We recommend that you mount your new power feeder to the machine table with through bolts, nuts, and washers (Figure 9). This option will give the most rigidity and clamping strength to prevent the feeder base from twisting out of alignment during use. However, if under-table support webs interfere with washer or nut locations under the table, you must use an optional clamping kit, or drill and thread holes directly into the table as described in Direct Mounting. Direct Mounting Use the included mounting template to drill and tap your table, so the power feeder base can be directly mounted to the table surface (Figure 10). if the table is thinner than %" thick where the threaded holes would be drilled and tapped, or if support webbing is in the way, the threads may strip or loosen as the power feeder is used. Thread locking compound will not cure this situation. Revert to the Through-Bolt Mounting option. in any case, make sure to use a mediumgrade liquid thread locking compound on all threads. Figure 9. Through-bolt mounting. -16- Model G4181/G7873 1-HP Power Feeder Test Run once power feeder assembly is complete and mounted on the table, you must test run your power feeder to make sure it runs properly. if, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the power feeder immediately, then review the Troubleshooting table on Page ???. if you still cannot remedy a problem, contact our Technical support at (570) 546-9663 for assistance. ▲warning û/j Loose hair, clothing, or jewelry could get caught in machinery and cause fl serious personal injury. Keep these items away from moving parts at all times to reduce this risk. To test run the power feed: 1. Read the entire instruction manual first! 2. Make sure all tools and foreign objects have been removed from the tabletop area. 3. Make sure that the power feeder gearbox oil level is full, the oil level should be 1" below the oil fill port. see Figure 15 for oil fill port location. 4. Ensure that all tools and objects used during set up are cleared away from the machine. 5. Adjust and lock the power feeder so the wheels are held approximately one inch above the table and nothing will interfere with wheel rotation. 6. Connect the power feeder to the power supply and use the feed direction switch (Figure 11) to test operation in both directions and both speeds. — Listen and watch for abnormal noises or vibrations. The power feeder should run smoothly. —Correct for any unusual noises or vibrations before operating the power feeder any further. always disconnect the power feeder from power when investigating or correcting potential problems. Figure 11. Feed direction and speed switch. Model G4181/G7873 1-Hp power Feeder -17- SECTION 4: OPERATIONS Operation Safety Basic Use and Care ▲WARNING You MUST assemble all guards, fences, and hold-downs before starting your machine or power feeder. Failure to heed this warning could result in amputation or death! ▲WARNING To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations. ▲WARNING Damage to your eyes and lungs could result from using woodworking machinery without proper protective gear. Always wear safety glasses and a respirator when operating this machine. ▲WARNING Loose hair, clothing, or jewelry could get caught in machinery and cause serious personal injury. Keep these items away from moving parts at all times to reduce this risk. NOTICE if you have never used this type of machine or equipment before, WE STRONGLY RECOMMEND that you read books, trade magazines, or get formal training before beginning any projects. Regardless of the content in this section, Grizzly industrial will not be held liable for accidents caused by lack of training. Power feeders reduce kickback hazards and improve cutting results by feeding in a consistent and stable manner. Remember, do not to stand in the path of potential kickback. When not in use, support the power feeder with a wooden block so the rubber wheels are raised above the table and do not compress from the weight of the power feeder. The universal joints on this power feeder allow you to adjust the power feeder tracking and height to accommodate many workpiece sizes. Before loosening any lock lever, always support the power feeder with a block of wood, so the power feeder does not drop and cause damage. Adjust the power feeder so it is toed-in approximately 1° to 1.5° degrees towards the machine fence. This adjustment will ensure that the power feeder wheels slightly push the workpiece against the fence during cutting ...
Dieses Handbuch ist für folgende Modelle:Schweißtechnik System - Power Feeder G7873 (3.57 mb)